User manual PALSONIC MODEL 6826G

[. . . ] OWNER'S MANUAL 68CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 6826G Type Tested Electrical Safety AS/NZS 3250 Lic 4166 Standards Australia APP No: N15899 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain this manual in an easily accessible location for future reference. * Screen displays and illustrations in this manual may differ from the actual ones for better visibility. Contents INTRODUCTION Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 NOTES FOR OPERATION Cautions for safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Using the direct select buttons To select a one-digit position number (0-9) METHOD 1: Press the button and the screen displays "X- -", wait for 2 seconds and the channel is selected. METHOD 2: Press 0 button and the screen displays "0- -", then press 0 button again, the screen displays "00-" then press the numbers. (The period of two-press must be within 2 seconds). To select a two-digit position number (10-99) METHOD 1: Press these two numbers and the screen displays "XX -", (The period of two-press must be within 2 seconds). Wait for 2 seconds and the channel is selected. METHOD 2: Press 0 button first, than press these two numbers, the screen displays "0XX", the channel is selected. (The period of two-press must be within 2 seconds). To select a three-digit position number (100-255) Press these three numbers and the screen displays "XXX" the channel is selected. (The period of two-press must be within 2 seconds). NOTE: If the input number is over 255, the screen will remain at the current viewed program. After 2 seconds X-X X-XXXX X-XXXXX Using the CH buttons 3 Press CH to select lower position numbers; CH to select higher ones. 2 1 Using the PREVIOUS channel button ( ) 11 2 When there are no menus on the screen, pressing the button on the remote controller (below the MENU button) can swap the current viewed channel with the previous one. For example, the channel you previously watched is 11, the present channel is 2, press the button, it will return to channel 11, press the button again it will return to channel 2. Using the channel SCAN button Press SCAN button, the set will scan the channels from first channel to higher channels one by one, every program will be displayed for about 3 seconds and then go on scanning until all programs are scanned over and then return to your former viewed program. During the scanning, press SCAN button again, the set will return to your former viewed program. 12 OPERATION Convenient Picture Controls Selectable picture To select the picture mode You can select the picture quality instantly among three preset modes and one user-set mode. Press the P. S button to select the desired picture quality. BRILLIANT, NATURAL, MELLOW and PERSONAL (user-set) can be selected cyclically. BRILLIANT NATURAL MELLOW PERSONAL To set the desired picture quality to the PERSONAL position 1. Press the MENU button to display the (PICTURE) menu. Or press the P. M button, to call up PICTURE menu. COLOR BRIGHT CONT SHARP 76 75 100 50 2. Press the or button to select the desired adjusting item, and press the or button to adjust the level. SELECT ADJUST Pressing (PERSONAL) Item COLOR BRIGHTNESS CONTRAST SHARPNESS *TINT paler darker weaker softer purplish deeper lighter stronger sharper greenish BRILLIANT 75 75 100 50 NATURAL 50 50 90 40 MELLOW 50 50 70 30 * TINT is for NTSC system only. The adjusted level is stored in the PERSONAL position. 13 OPERATION Convenient Sound Controls and Sleep timer Adjusting the volume and muting the sound To adjust the volume Adjust the volume with the VOL Press the VOL Press the VOL buttons. button to decrease the sound. button to increase the sound. To mute the sound The muting function is convenient when you need to pay attention to surrounding sounds, answer a phone call, receive a visitor, etc. 1. Press the MUTE button to mute the sound. To restore the sound, press the MUTE button again or VOL buttons. Sleep timer SLEEP timer Making use of the Sleep timer function allows you to have the set automatically turned off after a preset time, and the TV set set to standby mode. [. . . ] Refer to the owner's manual of the equipment to be connected as well. To connect AV input terminal You can connect video equipments such as a VTR and video camera to this TV and enjoy the high quality picture and sound. If your video equipment has a S-VIDEO output terminal, connect it to the S-VIDEO input terminal (special S-VIDEO type) of the unit. If not, connect it to the VIDEO terminal (phono type). To audio outputs Video camera etc. To video output VTR without S-VIDEO terminal Aerial output TO ANT IN TO ANT IN Aerial output VTR with S-VIDEO terminal To audio outputs To video output To audio outputs To S-VIDEO output terminal yellow (video) white (audio L/MONO) red (audio R) 20 CONNECTING OTHER EQUIPMENT To connect AV input terminal (continued) To select the video input, press TV/AV the button on the TV set or AV button on the remote controller repeatedly until you see the corresponding input indication on the screen. [. . . ]