User manual PALSONIC MODEL 76WSHD 1

[. . . ] OWNER'S MANUAL 76CM WIDE SCREEN HDTV READY MODEL: 76WSHD Type Tested Electrical Safety AS/NZS 3250 Lic 4166 Standards Australia APP No: N18748 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 Congratulations on your purchase of Palsonic's HDTV ready. Contents 2. 1 2. 2 2. 3 2. 4 We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this equipment. Retain this manual in an easily accessible location for future reference. * Screen displays and illustrations in this manual may differ from the actual ones for better visibility. 1 3 3 3 4 5 6 6 7 7 8 8 9 9 10 10 11 11 1. [. . . ] 3) Press VOL button (2) to select SKIP (ON). Thus, when you select channels with CH button (3), this channel will then be skipped. 4) To restore a skipped position number, select the position number you want to restore with the number buttons, enter into the PRESET menu to select SKIP X (OFF). 7. 4 Fine Tune When picture and sound's effect of a channel is poor (for example, one or two CATV channel's picture and sound are not standard), you can correct them by making use of Fine Tuning. 7. 4. 1 AFC (Auto Frequency Control) 1) Press the number buttons (4) or CH button (3) to select the channel you want to fine-tune. 2) Enter into the PRESET menu, press CH button (3) to select AFC, then press VOL button (2) to select AFC to activate it, the set begins fine-tune until the optimum picture and sound is achieved. (4) (3) (2) (1) (2) (3) To use AFC is recommended. If you are not satisfied with the effects after the AFC, you can shut down AFC and make use of FINE TUNE until you get satisfied effect. 7. 4. 2 FINE TUNE 1) Press the number buttons (4) or CH button (3) to select the channel you want to fine-tune. 2) Enter into the PRESET menu, press CH button (3) to select Fine tune, then press and hold the VOL or VOL button (2) to begin fine-tune until the optimum picture and sound is achieved. (4) (3) (2) (1) (2) (3) ! Note: if some channel's colour or sound is abnormal, it may be that the setting of the colour or the sound system is wrong, please do adjustment according to "8. 6 The setting of colour and sound system" to set the proper colour and sound system. 7. 5 VCR When receiving VCR programs, there may occur jump of the picture or bend of upper picture. You can solve this problem by activating VCR function. Please do the following steps: Enter into the PRESET menu, press CH or CH button to select VCR item, and press VOL or VOL button to set VCR (ON). If you do not meet this problem, or the signal source is not from VCR, please shut off this function. 7. 6 The setting of colour and sound system 7. 6. 1 Use OSD button (1) PAL 6. 5MHz 100Hz MOVING Press OSD button (1), the screen will display position number, colour and sound system. Check whether the colour and sound system is correct. 7. 6. 2 The setting of colour system 1) Press the number buttons (4) or CH button (3) to select the channel you need to set the colour system. (3) 2) Enter into the PRESET menu, press (2) CH button (3) to select SYSTEM, then press VOL button (2) to select proper colour system. Every time you press VOL or VOL button (2), the colour system will change in the sequence below: AUTO PAL SECAM PAL60 N443 (4) (1) (2) (3) NTSC In normal circumstances, please set the colour system to AUTO, and the set can automatically select the proper colour system. If colour is still abnormal, then select the proper colour system manually. 7. 6. 3 The setting of sound system (4) (3) (2) (1) (2) (3) 1) Press the number buttons (4) or CH button (3) to select the channel you need to set the sound system. 2) Enter into the PRESET menu, press CH button (3) to select SOUND, then press VOL button (2) to select proper sound system. Every time you press VOL or VOL button (2), the sound system will change in the sequence below: 4. 5MHZ 5. 5MHZ 6. 0MHZ 6. 5MHZ 8. Channel selection You can select your desired TV program by one of the following methods. 8. 1 Using the direct select buttons (0-9 & -/-- button) To select a one-digit position number (1) Press -/-- button to display "-" on the top right screen. (2) (1) (2) Press 0-9 number buttons to select a channel. - 8 To select a two-digit position number (1) Press -/-- button to display "--" on the top right screen. (2) (1) (2) Then press 0-9 to select a channel number. -- 28 To select a three-digit position number (1) Press -/-- button to display "---" on the top right screen. (2) (1) (2) Then press 0-9 to select a channel number. --- 128 8. 2 Using the CH or CH buttons (3) (1) (2) Press CH (1) to select higher position numbers; CH (2) to select lower ones. 28 8. 3 Using the PREVIOUS channel button ( ) Press the button on the remote controller can swap the current viewed channel with the previous one. ! Note: Pressing the button can also switch between programs from RF, AV1, AV2, AV3, DVD IN, HDTV IN (but this button can not be used to switch between YPbPr and XGA). 8. 4 Using the PREVIEW button Press PREVIEW button to start scanning from the current channel to higher channel, 16 subpictures will fill up the whole screen one by one. You can press one of P. SCAN, PHOTO, DYNAMIC, STILL, 0-9, -/-- , buttons on the remote controller to select a corresponding channel program. The menu of 16 picture These buttons' arrangement is in accordance with the arrangement of the program menu, each button represents the corresponding program. (4) Press the DYNAMIC button, the corresponding program is displayed on the main screen. If there are more than 16 programs, a new series of programs from 17th program will be displayed in turn, overwriting the previous screen until all the programs be displayed, and then recycle. 9. Picture and sound adjustments 9. 1 Picture adjustment 9. 1. 1 Making use of PERSONAL button Bright Soft Display more brightness and contrast pictures Display soft pictures Display the picture that you have adjusted in PICTURE menu (3) (2) (1) (2) (3) (4) Personal Standard Display normal pictures You can select the picture quality instantly among three preset modes and one user-set mode. Press the PERSONAL button (4) to select the desired picture quality. STANDARD, BRIGHT, SOFT and PERSONAL (user-set) can be selected cyclically. In these settings, brightness and contrast are different. [. . . ] 9300: It's used to set the state of colour temperature which suits for general user. 14. 7 Audio adjustment To adjust Bass, Treble, Surround sound, Balance, please switch to RF mode and operate them (please refer to Sound adjustment on page 23 and 24 ). The audio effects you get in RF mode also function in HDTV mode. 15. Display mode setting In factory the set has been set with multi display modes which are frequently-used at present. With the development of digital processing technology, in the future there are external equipment with different display modes. [. . . ]