User manual PALSONIC TFTV510

[. . . ] OWNER'S MANUAL 51CM CORDLESS REMOTE LCD TV/MONITOR MODEL: TFTV-510 Type Tested Electrical Safety AS/NZ 3250 Standards Australia PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 Congratulations on your purchase of this Palsonic LCD TV/MONITOR. We recommend that your thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this LCD TV/MONITOR. Retain this manual in an easily accessible location for future reference. Note: Screen displays and illustrations in this manual may differ from the actual ones for better visibility. Contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] CH+/-: to select a higher/lower numbered channel or cycle through the menus. VOL+/-: press to raise/lower the volume or adjust the selected item. Indicator: standby mode: red power on: yellow 7. Remote sensor 5 Back AUDIO IN PHONE SPEAK OUT TUNER POWER IN S-VIDEO input VGA input Earphone jack PC audio line in Antenna input AC Power input Video/audio input Speaker output 6 Remote control Remote control Power on/standby Muting Sound Channel select In PC mode, auto correct picture Press the button to switch the set among TV/AC/S-VIDEO/PC Clock/Timer setting Previous channel To enter into menu On-screen display Channel up/down selector. In menu operations, used to select item upwards or downwards. Press to adjust picture (including brightness, contrast, saturation and sharpness). In menu operation adjust the selected item or access the sun-menu. Setting sleep timer To select different picture modes 7 Battery Installation Please install the batteries before using the remote control. Open the battery cover. Install two "AA" batteries matching the +/- polarities of the battery to the +/marks. Replace the battery cover. Effective remote range Notes: 1. When the remote control will not be used for a long period of time or when the batteries are worn out, remove the batteries. There should be no obstacle between the TV and the transmitter. Use the remote control within the effective range 30 30 as the left figure. If the remote control does not work, please check whether the batteries are exhausted or the polarity is wrong. When direct sunlight, and incandescent lamp, fluorescent lamp or any other strong light shines on the remote sensor of the TV, the remote operation may be unstable. Different batteries have different features. Please don't mix different- type batteries. 5m 8 Installation Antenna connection/Power connection/Elevation adjustment Antenna connection Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area. Tuner Notes: Turn off the power firstly when you connect an outdoor antenna to the antenna input terminal. When installing an outside antenna system, extreme care should be taken to keep from touching power lines or circuits as contact with them might be fatal. In thunder and lightning weather, please disconnect the outdoor antenna to avoid thunder/lightning strike. 9 Power Connection Power cord To the wall outlet POWER IN Notes: 1. This TV can only be operated on a power of AC 240V 50 Hz. Please remove the power plug from the wall outlet when the TV will not be used for a long period of time. Elevation adjustment You can adjust the angle of the LCD TV as follows. The elevation can be adjusted from -50 to +150. 150 -50 10 Installation (continued) Connecting video/audio equipment Connecting video/audio equipment Composite VIDEO Signal Connection (RCA) Connect the composite signal terminal on the TV to the output of AV equipment through composite cable as illustrated. [. . . ] Press SLP button repeatedly to set sleep time between: 0, 10, 20, 30, 60, 90, 120, 180, 240 minutes. If you select 0 minute, it means the sleep timer function is turned off. SOURCE MENU CH VOL POWER Sleep 30 CHCH+ VOLVOL+ Using CLOCK button 1 Press CLOCK button, the Time menu appears. After setting Time menu, press CLOCK button to display Turn on menu. Press CH+/- to select item (hour, minute, status, the selected item is displayed in blue). [. . . ]