User manual PANASONIC AG-7350

[. . . ] TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE POWER CORD PLUG FROM THE AC RECEPTACLE. CAUTION: Danger of explosion or fire if battery is mistreated. For Battery Pack · Replace only with same or specified type. · Do not disassemble or dispose of in fire. · Do not store in temperatures over 60°C (140°F). [. . . ] Using [STOP] and [STILL], select "YES". 45 Outputting images to an external monitor for playback You can connect an external monitor to the output connector of the unit, output clips to the external monitor and play them back on the monitor. AUDIO OUT CH1/ CH2 connectors VIDEO OUT connector Component signal output OUTPUT connector (D4 CH 1 AUDIO CH 2 VIDEO HD/SD-SDI connector) HD/SD-SDI OUT COMPONENT OUT 1394 connector This unit External monitor HD/SD-SDI output AG-7350 Video output/ component output Setting the outputs 1 Hold down [POWER] for at least 2 seconds to turn the power on. 2 Press [MODE]. The thumbnail display off screen appears. 3 Press [MENU]. 4 Using [STOP] and [PLAY], select "AV OUT SEUP" setting item, and press [STILL]. 5 Using [STOP] and [PLAY], select item, and press [STILL]. 6 Press [MENU] to end the procedure. 46 CMPNT/SDI SEL : This is used to set the format of the D connector output and HD/SD-SDI output signals. Signals are output in the format in which they were recorded. 720p signals are cross-converted to 1080i signals, and output. 480i format signals are output; 720p/1080i signals are down-converted to 480i and output. Signals are output in the format in which they were recorded. 720p signals are cross-converted to 1080i signals, and output. · While signals from an external device are being recorded, do not change the format of the signals which are being output from the external device. Otherwise, it will not be possible for the signals to be recorded properly. · Once the 1394 cable has been connected to the 1394 connector, do not subject the connector to heavy external loads. · When recording signals from external devices, no guarantees are made concerning the playback images. (This function is provided solely for monitoring the images. ) · The automatic video recording function on a DVD component may not work properly. If this is the case, record the images manually. 2-slot continuous recording If P2 cards have been inserted into both of the P2 card slots, you can continuously record images first on one card and then on the other. While images are being recorded on one card, you can replace the other card with a fresh card and in this way record continuously onto 3 or more cards. (This is called hot swap recording. ) However, the fresh P2 card may not be recognized when it is inserted into the empty slot at certain timings (Before and after when recording continuously from one slot to the other). It is recommended that you insert a fresh P2 card while the card on which images are being recorded still has at least one minute of remaining memory. When "SLOT SEL" is assigned to [USER] using the "USER" item (page 74) on the "SW MODE" screen, you can change the slot targeted for recording at the touch of a button. · Changing slots is not possible while recording is in progress, so do this in the recording standby status. [. . . ] Saved in this file is the information of the last clip recorded by the P2 device. In order to prevent any of the information from being lost when transferring the data on a P2 card to a personal computer or writing the data stored in a personal computer onto a P2 card, be absolutely sure to download the "P2 viewer" dedicated software from the following web site and use it for this purpose. (Operating systems supported: Windows XP, Windows 2000) (Japanese) https://eww. pavc. panasonic. co. jp/pro-av/support/cs/csregistp2m/p2indexj. html (English) https://eww. pavc. panasonic. co. jp/pro-av/support/cs/csregistp2m/p2indexe. html When transferring data to a personal computer using a regular IT tool such as Microsoft Windows Explorer or Apple Finder, proceed as follows. To return the data to the P2 card, be absolutely sure to use the P2 viewer. · Transfer the data together with the CONTENTS folder and LASTCLIP. TXT file. [. . . ]