User manual PANASONIC AG-7350P

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. indicates safety information. CAUTION: Danger of explosion or fire if battery is mistreated. For Battery Pack Replace only with same or specified type. Do not disassemble or dispose of in fire. Do not store in temperatures over 60C (140F). [. . . ] For this reason, bear in mind that making a change in the format or frame rate may result in discontinuity from the last time code value of the previous recording. Recording format 1080i/24P 1080i/24PA 480i/24P 480i/24PA 720P/60P 720P/30P 720P/24P 720P/24PN Frame rate -- 24 -- Time code adjustment Adjustable in 5-frame increments Adjustable in 4-frame increments Adjustable in 2-frame increments INPUT1 ON OFF INPUT2 OSD DATE/ TIME PHOTO SHOT AUDIO COUNTER RESET/TC SET ON OFF MIC POWER+48V START/ STOP ZEBRA REC OIS COUNTER RESET MULTI/ P-IN-P TITLE ZOOM LCD EVF DTL WFM /REW PLAY FF/ Camera or Remote control - VOL + REC A. DUB Press the MENU button when you have finished setting the time code. MENU 720P/30PN -- Push the Operation lever in the e direction to move to YES and press it again. TC PRESET PRESET OK?YES PUSH STILL NO 0 Setting user information Setting user information allows you to store 8-digit memo (information such as the date and time) in the hexagonal format on the sub code track area. User information is automatically saved in the memory and retained after you turn off the power. Set the user information. Push the Operation lever in the e or r direction to select user information characters. You can use numbers from 0 to 9 and letters from A to F. UB PRESET MONTH 00000000 1 Set the POWER switch to ON. In the setup menus, RECORDING SETUP screen UB MODE, select USER. For menu operation (Page 94) You can also use the menu buttons on the remote control. (Page 14) Example: In the CAM mode RECORDING SETUP MIC GAIN2 25M REC CH SEL TC MODE TCG TC PRESET UB MODE UB PRESET TIME STANP -50dB 2CH DF REC RUN USER OFF +/ : PUSH q / g SEL : PUSH t / y PUSH MENU TO RETURN Push the Operation lever in the q direction to move to the next digit, then push it in the er direction to select a character. Shooting OSD DATE/ TIME PHOTO SHOT START/ STOP COUNTER RESET MULTI/ P-IN-P TITLE ZOOM /REW PLAY FF/ - VOL + UB PRESET MONTH F0000000 PUSH MENU TO RETURN +/ : PUSH q / g SEL : PUSH t / y Push the Operation lever in the e or r direction to move to UB PRESET and press it again. RECORDING SETUP MIC GAIN2 25M REC CH SEL TC MODE TCG TC PRESET UB MODE UB PRESET TIME STANP -50dB 2CH DF REC RUN USER OFF PUSH MENU TO RETURN You can reset the user information to nothing by pressing RESET on the camera or the remote control. BARS SHUTTER SPEES SELECT CH1 SELECT CH2 SELECT INT(L) INPUT1 INPUT2 INT(R) INPUT2 INPUT1 ON OFF INPUT2 AUDIO COUNTER RESET/TC SET ON OFF MIC POWER+48V ZEBRA REC OIS PUSH MENU TO RETURN LCD EVF DTL WFM REC A. DUB Push the Operation lever in the r direction to move to YES and press it again. RECORDING SETUP MIC GAIN2 25M REC CH SEL TC MODE TCG TC PRESET UB MODE UB PRESET TIME STANP -50dB 2CH DF REC RUN USER YES Camera or Remote control Press the MENU button when you have finished setting the user information. MENU PUSH MENU TO RETURN (Continued on the next page) 1 Charging the built-in battery/Setting the time data (continued) 7 Push the Operation lever in the e direction to move to YES and press it again. UB PRESET PRESET OK?YES PUSH STILL NO 8 Press MENU twice to exit the menus. MENU Basic playback operations 1 POWER ON 1 OFF Turn the POWER switch to ON. While pressing the lock release, turn the POWER switch to ON. (The frame changes to blue. ) Pressing the Operation lever a second time deselects the thumbnail. To scroll the pages, press the PAGE (- or +) button. To Play back clips: Select a thumbnail and push the Operation lever in the q (playback) direction. (For details on playback, see page 63. ) Only clips recorded in the same format as the playback format (6 in the figure below) can be played back. 1 2 3 4 5 6 7 8 THUMBNAIL OPERATION PROPERTY META DATA LOAD RECORD USER CLIP NAME INITIALIZE PROPERTY EXIT ALL CLIP SAME FORMAT CLIPS SELECTED CLIPS MARKED CLIPS TEXT MEMO CLIPS SLOT CLIPS SETUP EXIT DELETE FORMAT REPAIR CLIP RE-CONNECTION EXCH. THUMBNAIL EXIT CLIP PROPERTY CARD STATUS DEVICES PROPERTY SETUP SYSTEM INFO EXIT Thumbnail screens are output only from the VIDEO OUT terminal. 1 Slot number display The number of the slot with the P2 card containing the clip indicated by the yellow frame is shown here. (The number appears in yellow. ) If a clip extends over the P2 cards in two slots, both numbers will appear in yellow. When one of the following warnings applies to an inserted P2 card, the frame around the slot number turns pink. 1) RUN DOWN CARD (page 91) 2) DIR ENTRY NG CARD (page 91) Thumbnails This is where the images representing the clips are displayed. (The initial images are displayed in the default setting. ) Thumbnail display status (Page 7) The types of clips displayed as thumbnails appear in this area. Clip numbers The clips are displayed in the order in which they were shot. (up to 2000) Clips in the wrong recording format or clips which cannot be played back for other reasons are shown in red. [. . . ] At this time, each clip will be provided with its own COUNT value. Example of recording (DVCPRO50) a clip on one P2 card: Same as CLIP NAME REC start REC/PAUSE (recording start) (recording pause) Recording duration = Approx. 15 min. * The COUNT value is indicated as a four-digit number. The COUNT value is incremented each time a new clip is captured if clip metadata has been read in and TYPE2 has been selected as the recording method. The COUNT value can be reset using the following procedure. [. . . ]