User manual PANASONIC AG-HPG10P

[. . . ] Memory Card Portable Recorder Model No. F0707K0 -M D Printed in Japan ENGLISH VQT1H84 For your reference Before operating this product, please read the instructions carefully and save this manual for future use. Menu Displays Editing Saving data Recording Playback Preparations AG-HPG10P Name of the parts Operating Instructions Introduction Read this first! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. indicates safety information. CAUTION: THE AC RECEPTACLE (MAINS SOCKET OUTLET) SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. [. . . ] Signals are output in the format in which they were recorded. 720p signals are cross-converted to 1080i signals, and output. 576i format signals are output; 720p/1080i signals are down-converted to 576i and output. The meta-data is superimposed onto the HD-SDI signals. The meta-data is not superimposed onto the HD-SDI signals. EDH is superimposed onto the SD-SDI signals. EDH is not superimposed onto the SD-SDI signals. (When SYSTEM AUTO FREQ is set to 59. 94 1080i Hz) 480i (When SYSTEM AUTO FREQ is set to 50 Hz) 1080i 576i SDI OUT SDI METADATA SDI EDH SET UP ON OFF ON OFF ON OFF This is used to set the setup level for NTSC output during down-conversion. · This item is not displayed on the menu when SYS TEM FREQ is set to 59. 94 Hz. 0% 7. 5%A The HD/SD-SDI output signals comply with the following standards. HD : SMPTE 292M, 296M, 299M SD : SD: SMPTE259M-C (480/59. 94i), ITU-R BT. 656-4 (576/50i) 47 Playback Recording data on P2 cards 1394 input recording You can connect a digital video component equipped with a 1394 connector, and digitally record video signals, audio signals or time codes, etc. Unit Digital component AG-HPG10 IEEE1394 input/output connector 1394 cable (optional accessory) 1 Hold down [POWER] for at least 2 seconds to turn the power on. The thumbnail screen appears. 5 As in step 4, after selecting "RECORDING SETUP" using [STOP] and [STILL], set the time code, user's bit and so on. For details, refer to setting menu "RECORDING SETUP" screen (page 72). 2 Press [MODE]. The thumbnail display off screen appears. 1 2 106 mn 6 Press the two [REC] buttons together. Recording now starts. · To stop the recording, press [STOP]. · While recording is underway, text memos or shot marks assigned to [USER] (page 74) can be inserted. HD720P 60 C H C H 1 2 3 Press [MENU]. 4 Using [STOP], [PLAY] and [STILL], select the "RECORDING SETUP" ­ "SYS FORMAT" setting, press [STILL], and ensure that the 1394 video input image format and the unit's recording format are the same. For details, refer to setting menu "RECORDING SETUP" screen (page 72). 48 · Before connecting or disconnecting the 1394 cable, you must turn off the power of the component connected to the unit. · When connecting the unit to a component which uses a 6-pin type of 1394 connector, thoroughly check the 1394 cable and shapes of the connectors at its ends before initiating the connection. Connecting the cable the wrong way round may result in damaging the unit's inside 6-pin type of 4-pin type of parts and trouble. Also connect the 1394 cable to the component connector connector equipped with the 6-pin connector first. · Before recording signals from an external device, check that video signals are being input. [. . . ] Do not perform any operations for the files under the CONTENTS folder. When copying data, copy the LASTCLIP. TXT file together with the CONTENTS folder. · When transferring the data on a multiple number of P2 cards to a personal computer, create the folder for each P2 card in order to prevent the same clip names from being overwritten. · Do not delete the data on P2 cards. [. . . ]