User manual PANASONIC AG-HPX500E

[. . . ] Operating Instructions Memory Card Camera-Recorder Model No. Model No. AG-HPX500P AG-HPX500E FRANÇAIS Pour des explications en français, veuillez vous reporter au CD-ROM fourni. Before operating this product, please read the instructions carefully and save this manual for future use. S0407T1067 -P D Printed in Japan ENGLISH VQT1G18-1 Read this first! CAUTION: In order to maintain adequate ventilation, do not install or place this unit in a bookcase, built-in cabinet or any other confined space. To prevent risk of electric shock or fire hazard due to overheating, ensure that curtains and any other materials do not obstruct the ventilation. FCC Note: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] · CANNOT DELETE Cannot delete clips. · CANNOT FORMAT Cannot format P2 cards or SD memory cards. · CANNOT REPAIR Cannot repair clips. · CARD FULL The P2 card does not have enough free space for recording. · WRITE PROTECTED The P2 card or SD memory card is writeprotected. · NO CARD A P2 card or SD memory card has not been inserted. · NO FILE There are no files (version upgrade files, etc. ). Chapter 4 Adjustments and Settings for Recording (CAC) indicator During a mode check, it indicates that lens chromatic aberration compensation (CAC) operates normally. 29 AWB, ABB error indication In a mode check, the status of AWB and ABB that do not operate normally is shown. Safety zone The range of the zone is indicated by the SAFETY ZONE item on the DISPLAY SETUP screen. · 4:3: This indicates the position which is cropped to 4:3. · 90%: This indicates the range (90%) in which signals can be displayed by an ordinary home-use TV set. P2 card playback data indication · EOS: End of stream. No more data is available in the forward playback direction. No more data is available in the rearward playback direction. · P2 SLOT: Appears when pressing the USER button to which SLOT SEL is assigned. Warnings · COPY INHIBITED Input of DV formats via the 1394 connector in MCR mode cannot be recorded normally since the contents are copyright protected. · EXTERNAL 1394 DISCONNECT When the 1394 CONTROL item of the OTHER FUNCTIONS screen of the setup menu is set to EXT and recording without connecting external units with 1394 terminal, this display appears. · INCOMPATIBLE CARD The card cannot be used since it does not comply with the specified standard. · DIR ENTRY NG CARD Indicates a card where folder location has become corrupted. This type of card cannot be used for special recording modes (interval, ONE SHOT and loop recording). A warning appears when such a P2 card is inserted in a P2 device or when recording is completed. · RUN DOWN CARD Indicates that a P2 card has nearly reached the end of its life. This warning message appears each time the card is inserted or recording is stopped, and it will continue to appear until the card is replaced with a P2 card with sufficient life remaining. Proper recording and playback may not be possible with a P2 card that is near the end of its life, so we recommend replacing it with another one as soon as possible. Viewfinder Screen Status Displays 71 Errors These are displayed when an error occurs in the unit, P2 card, tape, or other component. If the problem is not fixed by turning the power off and then on again, either replace the card or tape based on the error information, or consult with your dealer as to which one is to be purchased. [. . . ] HA16RX-4P (SW1) (Hirose Electric Co. ) 1 2 3 4 5 6 7 8 9 10 REMOTE CAM DATA (H) CAM DATA (C) CAM CONT (H) CAM CONT (C) R/C ON R/C VIDEO OUT R/C VIDEO GND NC UNREG 12V (max. 0. 6 A) GND 1 2 3 4 Panasonic Part No. HR10A-7R-6SC(71) (Hirose Electric Co. ) 8 1 <Note> Be sure to use correct polarity when using external power supplies. FRONT MIC IN 1 2 3 GND AUDIO IN (H) AUDIO IN (C) 1 2 3 4 7 6 5 Chapter 10 Specifications 10 9 2 3 4 Panasonic Part No. [. . . ]