User manual PANASONIC AG-LC35

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS--USE AND STORE ONLY IN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DRIPPING OR SPLASHING LIQUIDS, AND DO NOT PLACE ANY LIQUID CONTAINERS ON TOP OF THE EQUIPMENT. CAUTION: Do not install or place this unit in a bookcase, built-in cabinet or any other confined space in order to maintain adequate ventilation. [. . . ] The top can be set to any value from 2 to 200 using the rotary 2 control. The bottom can be set to any value from 2 to 200 using the rotary 3 control. The left can be set to any value from 0 to 680 using the rotary 4 control. The right can be set to any value from 0 to 680 using the rotary 5 control. The default setting in each of these cases is 12. If the top setting is changed, the bottom setting will change, and vice versa, in such a way that the total setting will not exceed 200. Similarly, if the left setting is changed, the right setting will change, and vice versa, in such a way that the total setting will not exceed 680. The left and right settings can be changed in 1-step increments. R1 R2 R3 R4 R5 Crop A 2 8 12 0 - 680 7 12 0 - 680 [DSK On/Off] setting R1 R2 R3 R4 R5 This is used to set the DSK on/off operations. [Slide DSK ME Trig Slide In Slide Out Speed IN/OUT] takes effect when [Title] has been selected for On/Off Off Off Off 8 [Key] and [Fill]. Whether the in or out operation is to be initiated during an 2 - 64 On Off Off ME transition is set using the rotary 2 control. Off 1 1 Whether the sliding in operation is to be initiated in the 2 2 horizontal or vertical direction during DSK ON is set using 3 3 the rotary 3 control. The default setting is 0. R1 R2 R3 R4 R5 PAN 1 On Off Off IN Ch L L R L+R Balance 0 L7 - 0 - R7 49 [Audio Effects] settings [EQ] equalizer setting This is used to set the equalizers. Set [On] or [Off] for all equalizers using the rotary 3 control. The [L Level] bass level can be set in 2 dB intervals to any value from ­14 dB to 0 to +14 dB using the rotary 5 control. The [H Level] treble level can be set in 2 dB intervals to any value from ­14 dB to 0 to +14 dB using the rotary 4 control. The default setting is [0]. R1 R2 R3 R4 R5 EQ 1 On Off On L Level 0 ­14 - +14 H Level 0 ­14 - +14 [EQ Mid] equalizer midrange setting The [M Level] midrange level can be set in 2 dB intervals to any value from ­14 dB to 0 to +14 dB using the rotary 3 control. The midrange frequency can be set to any value from 100 Hz to 10. 2 kHz using the rotary 4 control. Select [0. 5], [1], [2] or [5] for Q using the rotary 5 control. The default setting is [0. 5]. R1 R2 R3 R4 R5 EQ 1 MId M Level 0 ­14 - +14 Freq Q 1. 01KHz 100 Hz 10. 2 KHz 0. 5 1 2 5 0. 5 [Voice Change] (voice changer) setting This is used to set the voice changer. Set [On] or [Off] using the rotary 3 control. Set [Up] or [Down] for the [Pitch] using the rotary 4 control. [Level] can be set to any value from [0] to [10] using the rotary 5 control. [. . . ] Is the monochrome selection switch set to ON? Is only "Y" provided as input instead of the composite signal? Has the source been input correctly? There is no color. There is no sound. The image does not Has the same signal been selected for A-side and B-side?change even when the transition lever is moved during mix/wipe mode. MX-Navi-related problems Problem A menu for title load or playback etc. [. . . ]