User manual PANASONIC AG-LC35P

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS. [. . . ] · 1 Flashes: Card recognition underway, or a card other than that on which data is to be recorded in special recording mode · -- : No card inserted. · P : Write-protected · F : Full memory · X : Cannot recognize · E : a P2 card in an invalid format (Returns to normal if formatted. ) Chapter 4 Adjustments and Settings for Recording 70 Viewfinder Screen Status Displays 27 Special recording display This display appears when the REC FUNCTION option of the setting menu RECORDING SETUP screen is set to INTERVAL, ONE SHOT or LOOP, and when PRE REC is set to ON. A P2 card inserted in a free slot after start of a special recording mode is not used for recording. Insert P2 cards before start of recording. Stop special recording and insert the P2 card again. 28 Lens chromatic aberration compensation · FORMAT ERR !Indicates a P2 card that does not meet the P2 card standard. <Thumbnail operations> · CANNOT ACCESS Cannot access clips. · CANNOT DELETE Cannot delete clips. · CANNOT FORMAT Cannot format P2 cards or SD memory cards. · CANNOT REPAIR Cannot repair clips. · CARD FULL The P2 card does not have enough free space for recording. · P2 MICON ERROR: No P2 microcomputer response · P2 CONTROL ERROR: Trouble in P2 control · REC RAM OVERFLOW: Recording RAM overflow · TURN POWER OFF This message indicates that an abnormal event has occurred, for example, that a card has been removed during access or that a change in system frequency has been made. Turn the power off and then turn it back on again. · REC WARNING This is displayed when trouble has occurred during recording. If the warning persists, consult your dealer. · CARD ERR (1) (2) (3) (4) (1/2/3/4): Trouble has occurred in the P2 card found in the slot indicated by the number. If the warning continues, turn off the power. If the warning appears even when recording is carried out again, replace the card with another one. · ERROR: Other type of trouble · 1394 This is displayed when trouble has occurred in the 1394 connections or signals. · 1394 INITIAL ERROR: Connection error · 1394 INPUT ERROR: Input error · 1394 INPUT ERROR (OTHER FORMAT): (Wrong input format) · LOW BATTERY: Indicates that the battery is exhausted. Camera status display · AWB: AWB indicator · ABB: ABB indicator · AWB P3. 2 K/AWB P5. 6K: Displays the color temperature assigned to PRST when the WHITE BAL switch is set to PRST. Also displayed when AWB is performed in the PRST position. · GAIN **dB: Displayed when GAIN is switched. [. . . ] 16 minutes (When recorded in DVCPRO HD format using one AJ-P2C016RG card with audio signals recorded on 4 channels) P2 Card (4GB, 8GB, 16GB are available) × 4 slots MXF file (FAT32 file system) · Complies with SD format (MMC cannot be used) · 1 slot (for reading and writing camera setup data) Recording media: Recording file: SD memory card slot: * The recording time represents one shot continuously recorded on a P2 card. The recording time may be shorter depending on the number of shots recorded. HD video system Sampling frequency: Quantizing: Video compression system: Video compression rate: Video recording bit rate: Y: 74. 25 MHz, PB/PR: 37. 125 MHz 8 bits DCT + variable-length code 1/6. 7 100 Mbps Audio system Sampling frequency: Quantizing: Head room: 48 kHz 16 bits/4 CH 20 dB/18 dB (selectable) Chapter 10 Specifications Video Input/Output GEN LOCK IN: COMPONENT OUT: VIDEO OUT: SDI OUT: BNC × 1, 1. 0 V p-p, 75 D4 terminal (component), Y: 1. 0 V p-p, 75 , PB/PR: 0. 7 V p-p, 75 BNC × 1, 1. 0 V p-p, 75 · BNC × 1, 0. 8 V p-p, 75 · HD: compliant with SMPTE 292M/296M/299M · SD: compliant with SMPTE 259M-C/272M-A/ITU-R. BT656-4 Audio Input/Output MIC IN: · XLR × 2 (FRONT 1, FRONT 2) · high impedance · + 48 V (available) · MIC: ­40 dBu/­50 dBu/­60 dBu (selectable on menu) · XLR × 2 (REAR 1, REAR 2) · high impedance · LINE/MIC / + 48 V (selectable) · LINE: 0 dB · MIC: ­50 dBu/­60 dBu (selectable on menu) Pin jack × 2 (CH 1, CH 2), Output: 316 mV, 600 ø3. 5 mm stereo mini jack × 1 28 mm diameter × 1 AUDIO IN: AUDIO OUT: Headphone: Internal speaker: Dimensions and specifications 147 Other Input/Output TC IN: TC OUT: IEEE1394: DC IN: DC OUT: REMOTE: LENS: EVF: USB2. 0 (DEVICE): BNC × 1, 0. 5 V p-p to 8 V p-p, 10 k BNC × 1, low impedance, 2. 0 V p-p ± 0. 5 V p-p 6 pins, digital input/output (compliant with IEEE 1394) XLR × 1, 4 pins, DC 12 V (11. 0 V to 17. 0 V) 4 pins, DC 12 V (11. 0 V to 17. 0 V), max. 1. 5 A 10 pins 12 pins 20 pins Type-B, 4 pins (compliant with USB ver. 2. 0) LCD Monitor LCD monitor: 3. 5-inch LCD color monitor, 210, 000 pixels (4:3) Accessories Accessories: · 1. 5-inch viewfinder (4:3 CRT, NTSC/PAL switchable) · Shoulder strap · Ferrite core (2) · Front Audio Level control knob (page 101) · Control knob mounting screw · Component video cable · PIN-BNC conversion plugs (3) · CD-ROM · Operating Instructions Chapter 10 Specifications 148 Dimensions and specifications Connector signal description DC IN 1 2 3 4 GND NC NC +12V Panasonic Part No. [. . . ]