User manual PANASONIC AJ-D640

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Use of another battery may present a risk of fire or explosion. [. . . ] button is pressed, the following message <CMCR RA/RT > A AD EDWIE RA ED SLC EET : 1 WIE RT SLC EET : 1 CR CNI AD OFG RA UE DT ED SR AA TTE IL RA ?ED YS E N O TTE IL : : n dial button the arrow 6 Turn the JOG and press theto move button. (cursor) to YES, JOG dial When the data loading is completed, the following message appears. Select the file No. dial button move the 2 Turn thetoJOG SELECT itemtowhich comesarrow (cursor) the after READ, and press the JOG dial button. <CMCR RA/RT > A AD EDWIE EET : 1 n SLC RA ED SLC EET : 1 WIE RT CR CNI AD OFG RA UE DT ED SR AA TTE IL : <CMCR RA/RT > A AD EDWIE RA ED SLC EET : 1 WIE RT SLC EET : 1 CR CNI AD OFG RA UE DT ED SR AA TTE IL RA O ED K YS E N O n TTE IL : : To load the VTR unit's data, open the VTR CARD READ/WRITE screen, and perform steps 4 to 6. If one of the following messages appears when the JOG dial button is pressed, the data cannot be loaded. JOG to 3 Turn 1the 8, anddial buttonJOG select any number from to press the dial button. to move the arrow (cursor) to the READ <CMCR RA/RT > A AD EDWIE n SLC EET : 1 RA ED SLC EET : 1 WIE RT CR CNI AD OFG RA UE DT ED SR AA TTE IL : Error message READ NG NO CARD (setup card has not been inserted) READ NG FORMAT ERROR (formatting error) READ NG NO FILE (file not found) READ NG ERROR (the data cannot be loaded) Remedial action Insert the card. The card was formatted by a device other than the unit. Save the file data. Data saved by devices other than unit cannot be loaded. 7 Press the operations. 65 MENU button to exit the menu The setting menu is cleared, and the display showing the unit's current statuses appears at the top and bottom of the viewfinder screen. Cassette tapes Loading a cassette tape there are no cassette 1 Check thattop panel, andcables around theswitch to holder or set the POWER ON. <Note> When condensation has formed inside the unit, the HUMID display lights. Wait until this display is cleared before proceeding with the intended operation. HUMID display Checking for tape slack Gently push in the reel using your finger and turn the reel in the direction of the arrow. If the reel fails to turn, it means there is no tape slack. Ejecting the cassette tape While the power is still on, press the EJECT button to open the cassette holder, and take out the cassette tape. If another cassette is not going to be loaded immediately after this tape is ejected, close the cassette holder. POWER: ON 2 Press the EJECT button. The cassette holder opens. EJECT button Ejecting the cassette when the battery has no charge First, set the POWER switch to OFF to turn off the unit's power. tape where continuity 2 At the place on the the PLAY/PAUSE (or is to be maintained, press STOP) button again to stop the tape. It takes about 3 Press thetolens RET button. preparations for two seconds complete the the scene-to-scene continuity. During rec-pause The scene-to-scene continuity timing is located automatically. However, the time taken until the start of recording differs depending on the setting of the VTR SAVE/STBY switch. O When the VTR SAVE/STBY switch is set to SAVE, recording commences about two seconds after the VTR START button is pressed. O When the VTR SAVE/STBY switch is set to STBY, recording commences as soon as the VTR START button is pressed. Ensuring scene-to-scene continuity after the power was turned off while the unit was in the rec-pause mode 4 Press the VTR START button or lens VTR button to start the recording. 1, 2 3 1 Switch the power back on. 2 Press the VTR START button or lens VTR button to start the recording. 4 2 1 69 Playback (checking what has been recorded) When the PLAY/PAUSE button is pressed, the playback pictures can be monitored in black and white on the viewfinder screen. These playback pictures can be monitored in two other ways. Rec review When recording is temporarily stopped and the lens RET button is pressed, the last two seconds of the tape are automatically rewound, and the playback pictures on this part of the tape appear on the viewfinder screen. This makes it possible to check whether recording was performed properly. After the two seconds of the tape have been played back, the unit is again set to the recording start standby mode. If the RET button is held down, a maximum of 10 seconds of the tape is rewound and played back. <Note> The rec review function cannot be used unless recording lasts for one or more seconds. Color playback When an HD color monitor is connected to the unit's HD SDI OUT connector, color playback pictures can be monitored. [. . . ] CH1 and 1 Set the AUDIO SELECT CH1 and CH2 switch to 2 Set the AUDIO IN CH1 and CH2 switches to REAR. AUTO. on 2 Set the AUDIO IN CH1 and CH2 switches to 3 Set the LINE/MIC/+48V selector switch with the back panel to MIC or +48V in accordance the FRONT. the microphone connected to IN 3 Pointsuitable sound source, and the MICthat jack at a check the changes in the level displays for both CH1 and CH2 reflect the changes in the strength of the sound. source, and 4 Point the microphones at the soundaudio levels check that the changes in the displayed on the audio level meter of the display window and in the viewfinder reflect the changes in the strength of the sound. [. . . ]