User manual PANASONIC AJ-D850P

[. . . ] Digital Video Cassette Recorder AJP Operating Instructions IMPORTANT "Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws. " CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: To reduce the risk of fire or shock hazard, do not expose this equipment to rain or moisture. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER MOUNTING OF THE OPTIONAL INTERFACE BOARD TO AUTHORIZED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. [. . . ] Turn the search dial and move the cursor ( ) on the menu screen to any setup item except No. The USER1 settings are now stored in the memory. If the USER1 settings are not going to be stored in the memory, do not press the SET button but press the MENU button. 7 8 ­ 53 ­ Setup menus Saving a user file 1 2 3 Press the MENU button. While holding down the STAND BY button, press the REW or FF button, and select USER1. Turn the search dial and move the cursor ( A01 (SAVE). ) on the menu screen to setup item No. SETUP-MENU MENU <USER1> NO. A00 - 0000 803 TELETEXT DET AUTO A00 LOAD USER2 A01 SAVE USER2 A02 P. ON LOAD OFF END 4 While holding down the search button, turn the search dial and select the user file into which the USER1 contents are to be saved. User files which have been set to the lock mode are not displayed. When all the user files have been set to the lock mode, the "LOCKED" display appears and the contents cannot be saved. The following messages appear on the menu screen and counter display. Menu screen SETUP-MENU SAVE USER1 USER2 OK?YES<PLAY>/NO<STOP> Counter display TCR 00:00:00:00 SETUP SAVE U-1 U-2 5 The user file number selected in step 4 is displayed in the shaded area. 6 Press the PLAY button. The contents of the USER1 file are saved in the user file which was selected in step 4 and stored in the memory. When the STOP button is pressed, the USER1 menu display appears while the settings remain unchanged. Turn the search dial and move the cursor ( ) on the menu screen to any setup item except No. The USER1 settings are now stored in the memory. If the USER1 settings are not going to be stored in the memory, do not press the SET button but press the MENU button. 7 8 Automatic loading of user file when the power is turned on When the user file to be loaded is selected in advance using setup menu item No. A02 (P. ON LOAD), it can be automatically loaded into USER1 when the power is turned on. ­ 54 ­ Setup (setting) menus SYSTEM menu <SYSTEM> Item No. 0255 Setting Superimposed display ­127 . 128 Description System phase adjustment: Total variable range: ±180° or more ­: Advanced +: Delayed <Note> If setting operation is performed, the setting value does not return to factory (default) setting. System phase adjustment: SC cycle phase (280 ns steps) ­: Advanced +: Delayed <Note> If setting operation is performed, the setting value does not return to factory (default) setting. Video phase adjustment: 148 ns steps ­: C advanced +: C delayed 01 SYS H 0000 . 123 02 VIDEO PHASE 03 YC COARSE YC timing rough adjustment: 148 ns steps ­: C advanced +: C delayed 04 YC FINE YC timing fine adjustment: 37 ns steps ­: C advanced +: C delayed (The digital OUT option YC does not change. ) SCH phase adjustment: 90° units (The S and C phases change but the H phase does not change. ) SCH phase adjustment: Total variable range: ±45° or more (The S and C phases change but the H phase does not change. ) 05 SCH COARSE 06 SCH FINE 07 PB OUT LV Component PB output level adjustment: Total variable range: ±3 dB 08 PR OUT LV Component PR output level adjustment: Total variable range: ±3 dB The underline on the setting item denotes the initial setting. ­ 55 ­ Setup (setting) menus SYSTEM menu <SYSTEM> (continued) Item No. [. . . ] 1 2 3 Signal GND HOT COLD AUDIO OUT SERIAL OUT (DIGITAL) BNC × 3 AUDIO OUT (DIGITAL) CUE OUT TIME CODE OUT MONITOR OUT HEADPHONES (front) XLR × 2 XLR × 1 XLR × 1 XLR × 2 Mini-jack L (CH1)/R (CH2) AUDIO OUT (ANALOG) XLR × 2 CH1, CH2 (Option) CH1/CH2, AES/EBU format RS-422A REMOTE (9P) REMOTE IN/OUT Pin No. 1 2 3 Signal FRAME GROUND TRANSMIT A RECEIVE B Pin No. 4 5 6 Signal RECEIVE COMMON ------ ---- TRANSMIT COMMON Pin No. 7 8 9 Signal TRANSMIT B RECEIVE A FRAME GROUND REMOTE OUT Pin No. [. . . ]