User manual PANASONIC AJ-D910

[. . . ] This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. RB The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] The tape is rewound for a minimum of 2 or so seconds and a maximum of 10 or so seconds. When the REC REVIEW button is released, playback automatically starts from the point where the button was released until the REC PAUSE position, and the REC PAUSE mode is established. <Note> When the temporary stop mode has been released during a REC REVIEW operation, the REC command is accepted but recording starts after the tape is rewound to the frame-to-frame continuity point. When recording is started, the tape begins its approach, and recording with frame-to-frame continuity can be conducted. <Note> It is recommended that REC be selected as the setup menu item No. 105 setting to transfer to the recording mode more quickly. 6. Preventing erroneous recording operations O During recording, the unit will not respond to the pressing of any of the function buttons except STOP and PAUSE/STILL. (This is to prevent the transfer to another mode during recording. ) O When the KEY INHIBIT switch is set to ON, all the function buttons except for the ones set using setup menu item No. Under the initial settings, none of the function buttons except for STOP and EJECT will work. When ENA has been selected as the setup menu item No. 000 setting, all the function buttons are made operable. 5. Auto back function In order to ensure frame-to-frame continuity, this function automatically rewinds the tape for approximately 1 second after REC PAUSE and stops the tape. Playback is resumed when the PAUSE/STILL button is pressed again. When the PLAY PAUSE mode continues for 2 minutes, the unit will forward the tape for several frames to protect the cylinder heads and tape, and the STILL mode is established again. When the STILL mode has continued for over 30 minutes, the standby OFF (half-loading) mode is automatically established in order to protect the tape. 34 Playback 2. Cue playback and review playback When the FF button or REW button is pressed in one of the search modes (search still, FWD search, REV search, FWD search still or REV search still), the tape is cued or reviewed at the speed which was selected for the setup menu item No. Further, if the SEARCH button is pressed in the FF mode or REW mode, the tape is cued or reviewed at a reduced speed, namely, at the speed selected for the setup menu item No. When the PAUSE/STILL button is pressed during cue or review playback, the tape will be temporarily stopped. When it is pressed again, cue or review playback is resumed. VTR operating mode Function button SEARCH PLAY or STOP FF or REW PLAY or STOP FF SEARCH PLAY or STOP REW SEARCH PLAY or STOP Search still FF REW SEARCH FWD search (cue playback) REW PAUSE/STILL SEARCH REV search (review playback) FF PAUSE/STILL PAUSE/STILL, SEARCH or FF REW PAUSE/STILL, SEARCH or REW FF PLAY Any mode STOP STOP FF or REW PLAY or STOP FWD search (cue playback) PLAY or STOP REV search (review playback) PLAY or STOP FWD search (cue playback) REV search (review playback) FF REV search (review playback) FWD search still REW FWD search (cue playback) REV search still FWD search (cue playback) REV search (review playback) REV search (review playback) FWD search (cue playback) PLAY Transfer of VTR operation Search still FWD search still REV search still 35 Playback a 3. Linear 0. 3a speed playback The slow still mode is established when the SEARCH button is pressed during still-picture playback (PLAY PAUSE). Linear 0. 3a speed playback is performed by pressing the FF or REW button in this mode. When the PAUSE/STILL button is pressed during the linear 0. 3a speed playback, the tape is temporarily stopped. Linear 0. 3a speed playback is restored when the PAUSE/STILL button is pressed again. [. . . ] ° 5) RF warning display will flash during REC and REC PAUSE modes. When the unit changes from REC and REC PAUSE modes, the RF warning display will turn off. 57 Warning Systems Status display window (LCD) Item Warning Battery Remaining Warning tape display charge display status display display No display WARNING lamp Warning alarm Description of warning Operation of unit Remedial action No display Memory status Flashes 4 Sounds 4 times/second times a second error between °1) SYSCON and DV. for 3 seconds Error code Switch the power [00:00:00:11] will OFF and consult be displayed for 5 your local dealer. seconds in the time code display position in the status display window. [. . . ]