User manual PANASONIC AJ-D95DCP

[. . . ] Digital Video Cassette Recorder AJ- DCP Operating Instructions Printed in Japan VQT8017-3 F10399W3040 D P IMPORTANT "Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws. " CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER CHANGE OF SWITCH SETTING INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER MOUNTING OF THE OPTIONAL INTERFACE BOARD TO QUALIFIED SERVICE PERSONNEL. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. [. . . ] Press the MODE button to set each item in turn. To return to the menu screen, press the MODE button while holding down the PAGE button. How to return to the factory settings 1 2 Set the LOCAL/MENU/REMOTE switch to the MENU position. The unit is now set to the menu setting mode, and the menu screen appears on the video monitor. The unit is set to the default setting mode, and the default setting screen appears on the video monitor. 23 Setup (Initial Settings) SELECT 0 1 2 3 MODE ESCAPE LOAD SAVE PROTECT 3 Press the RESET button. The unit is set to the default setting mode, and the default setting screen appears on the video monitor. SELECT MODE ESCAPE LOAD SAVE PROTECT 3 Press the MENU-UP button or MENU-DOWN button to move the cursor to the LOAD position, and press the SET button. The unit is set to the LOAD mode, and the load screen appears on the video monitor. SET­UP MENU <LOAD> NO FACTORY (ALL) FACTORY (NOT SYSTEM) USER (ALL) USER (NOT SYSTEM) 0 1 2 3 4 Press the MENU-UP button or MENU-DOWN button to move the cursor to the SAVE position, and press the SET button. The unit is set to the SAVE mode, and the save screen appears on the video monitor. SET­UP MENU <SAVE> NO USER (ALL) USER (NOT SYSTEM) 4 Press the MENU-UP button or MENU-DOWN button to move the cursor to FACTORY (ALL), and press the SET button. O If this operation is performed with the cursor moved to FACTORY (NOT SYSTEM) instead, all the factory settings except for the SYSTEM menu settings will be restored. O If this operation is performed with the cursor moved to NO, the factory settings are not restored, and operation is returned to the menu screen. Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position. This completes the menu settings. 5 5 Press the MENU-UP button or MENU-DOWN button to move the cursor to USER (ALL), and press the SET button. O If this operation is performed with the cursor moved to USER (NOT SYSTEM) instead, all the settings except for the SYSTEM menu settings will be updated. O If this operation is performed with the cursor moved to NO, the settings are not updated, and operation is returned to the menu screen. The screen for checking the SAVE operation appears. Press the MENU-UP button or MENU-DOWN button to move the cursor to the YES position, and press the SET button. The settings are now saved in the memory. SAVE OK? 6 How to set the user defaults 1 2 Set the LOCAL/MENU/REMOTE switch to the MENU position. The unit is now set to the menu setting mode, and the menu screen appears on the video monitor. Perform steps 2 through 6 of "Setting method using on-screen menus, " and change the items to the desired settings. [. . . ] 2 Use a Phillips head screwdriver to push in and turn the red plastic screw part counterclockwise. (This screw needs to be rotated about 30 turns before unloading can be started. ) 3 Insert the take-up jig (packed with the unit) into the tape ejection slot (on the mechanism side of the VTR), and rotate the flange part (white gear) of the supply reel in the take-up direction to take up the tape slack using the rubber part of the take-up jig. <Note> Take care not to damage the tape in any way. 4 Once more use the Phillips head screwdriver to push in and turn the red plastic screw part counterclockwise. [. . . ]