User manual PANASONIC AJ-HD130

[. . . ] Digital HD Video Cassette Recorder AJ- DCP Operating Instructions IMPORTANT "Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws. " CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] SAVE OK? 2 How to set the user defaults 1 2 3 NO YES Set the LOCAL/MENU/REMOTE switch to the MENU position. The VTR is set to the menu setting mode, and the menu screen is displayed on the video monitor. 7 Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position. This completes the menu settings. Perform steps 2 through 6 in "How to perform settings using the on-screen menu, " and change to the desired settings. Press the RESET button. The VTR is set to the default setting mode, and the default setting screen is displayed on the video monitor. SELECT MODE 2 0 ESCAPE 1 LOAD 2 SAVE 3 PROTECT 21 Setup (Initial Settings) How to load the user defaults How to protect the menus By setting the unit to the menu protection mode, opening of the setup menus can be prevented even when the LOCAL/MENU/REMOTE switch on the front panel has been set to the MENU position. 1 2 Set the LOCAL/MENU/REMOTE switch to the MENU position. The VTR is set to the menu setting mode, and the menu screen is displayed on the video monitor. 1 2 Press the RESET button. The VTR is set to the default setting mode, and the default setting screen is displayed on the video monitor. SELECT MODE 2 0 ESCAPE 1 LOAD 2 SAVE 3 PROTECT Set the LOCAL/MENU/REMOTE switch to the MENU position. The VTR is set to the menu setting mode, and the menu screen is displayed on the video monitor. Press the RESET button. The VTR is set to the default setting mode, and the default setting screen is displayed on the video monitor. SELECT MODE 2 0 ESCAPE 1 LOAD 2 SAVE 3 PROTECT 3 Press the MENU-UP button or MENU-DOWN button to move the cursor to the LOAD position, and press the SET button. The VTR is set to the LOAD mode, and the LOAD screen is displayed on the video monitor. SET­UP MENU <LOAD> 2 NO FACTORY USER (ALL) USER (NOT SYSTEM) 3 Press the MENU-UP button or MENU-DOWN button to move the cursor to the PROTECT position, and press the SET button. The VTR is set to the menu protection setting mode, and the screen for checking the menu protection function is displayed on the video monitor. 2 NO YES 4 Press the MENU-UP button or MENU-DOWN button to move the cursor to USER (ALL), and press the SET button. O If the cursor is moved to USER (NOT SYSTEM) and this operation is performed, operations are performed using the user settings stored in the memory for all the menus with the exception of the SYSTEM menu. O If the cursor is moved to NO and this operation is performed, operation returns to the menu screen while the user settings stored in the memory remain unchanged. Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position. This completes the menu settings. 4 Press the MENU-UP button or MENU-DOWN button to move the cursor to YES, and press the SET button. The menu screen now appears. 5 22 Setup (Initial Settings) 5 Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position. The unit is now set to the menu protection mode. When the LOCAL/MENU/REMOTE switch is set to the MENU position, the VTR is not set to the menu setting mode, and "MENU PROTECTED" appears on the video monitor screen. [. . . ] 2 Use a Phillips head screwdriver to push in and turn the red plastic screw part counterclockwise. (This screw needs to be rotated about 30 turns before unloading can be started. ) 3 Insert the take-up jig (packed with the unit) into the tape ejection slot (on the mechanism side of the VTR), and rotate the flange part (white gear) of the supply reel in the take-up direction to take up the tape slack using the rubber part of the take-up jig. <Note> Take care not to damage the tape in any way. 4 Once more use the Phillips head screwdriver to push in and turn the red plastic screw part counterclockwise. [. . . ]