User manual PANASONIC AJ-HD1400P

[. . . ] Operating Instructions Digital HD Video Cassette Recorder Model No. AJ- P E Before operating this product, please read the instructions carefully and save this manual for future use. F0606T1086 -F D Printed in Japan ENGLISH VQT0X83-1 Read this first! For AJ-HD1400P and AJ-HD1400E _THIS APPARATUS MUST BE GROUNDED To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power outlet which is effectively grounded through normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to the ground. Incorrectly wired extension cords can be extremely hazardous. The fact that the equipment operates satisfactorily does not imply that it is grounded, and the installation is not necessarily safe. [. . . ] DVCPRO P playback is not possible. 032*1 REC REF *1 Displayed menus may vary depending on the settings in menu No. For details, refer to "Menus which are displayed" (page 32). "_____" indicates the factory setting. 39 Setup menus (continued) OPERATION No. /Item 100 SEARCH ENA Description of setting To set the transition method to search mode (stick operation). 0000 STICK : Shift to the search mode when the SEARCH button is pressed or when the stick is operated. 0001 KEY : Do not shift to the search mode unless the SEARCH button is pressed. For setting the maximum speed in the shuttle mode. 0000 X8. 4 : 8. 4k normal speed 0001 X16 : 16k normal speed 0002 X32 : 32k normal speed <Note> The maximum speed for the HD SP mode is automatically limited to 25k normal speed. No. /Item 107* EE MODE SEL 1 Description of setting For setting the HD SDI and HD analog component output signals in EE mode when HD SDI input is selected. 0000 NORMAL : Signals delayed by the time taken by internal signal processing are output. 0001 THRU : Signal processing is not undertaken internally, and the signals are output without delay at their original timing. <Notes> The superimposed information is not displayed when THRU is used as the setting. When 1394 or SG is selected for the input signal in edit mode, internal signal is selected forcibly "NORMAL". 101 SHTL MAX 102 For setting the maximum speed of fast forward or FF. REW MAX rewind operations. 0000 X16 : 16k normal speed 0001 X32 : 32k normal speed 0002 X50 : 50k normal speed <Notes> The maximum speed for the HD SP mode is automatically limited to 25k normal speed. The maximum speed for the DV and DVCAM modes is automatically limited to 32k normal speed. 104 For setting whether a warning is to be displayed when REF ALARM the REF VIDEO signal is not connected. 0001 ON : A warning is displayed by the flashing STOP lamp. 105*1 AUTO EE SEL For setting the mode of the VTR, which becomes the EE state when menu item No. 140 OUTPUT is set to "EE. " 0000 S/F/R : The mode changes to the EE state when this item is set to STOP, FF, or REW. 0001 STOP : The mode changes to the EE state only when this is set to STOP. For setting the output conditions of video images and voice when ejecting the tape. 0000 EE : Both the video and audio signals are always output in the EE (electric modulation to electric playback) mode regardless of the setting of the menu No. 140 OUTPUT. 0001 BLACK : The output status differs according to the setting of the menu No. 140 OUTPUT. [. . . ] and then to ON again. If a problem has been encountered in communication between the E-78 Set the POWER switch to OFF STOP servo microcomputer and mechanism relay board, this error number and then to ON again. E-bA BATTERY This appears when the input DC voltage has dropped below the undercut voltage. Check the output voltage of the equipment supplying DC STOP power. <Note> Consult your dealer if the error message display persists even after the unit has been restarted. 63 Emergency eject Procedure to ejecting the tape manually in an emergency If the cassette tape fails to be ejected even when the EJECT button is pressed, it can be ejected as follows. Follow the steps below after making absolutely sure that the unit's power has been turned off. 1 2 Remove the top panel. [. . . ]