User manual PANASONIC AJ-D200

[. . . ] To download the relevant source code, visit http://panasonic. biz/sav/. Please note that we cannot answer any questions you may have about the content, etc. of any source code you may obtain from the above Web site. 2. This product includes software licensed under the ICU License. [. . . ] Position the WHITE BAL switch at [PRST]. 3 Press the JOG dial button to display the following message: WHITE BAL Switch 3 With the AUTO W/B BAL switch flipped up, turn on the POWER switch. This resets all settings for USER menu options to their defaults. 59 4-10-4 How to Use Scene File Data It is possible to write the settings data into the scene file area of the internal memory of the AJ-D200P, or to read data written in this area. Four types of scene files are available. This data allows you to quickly reproduce an optimum setup state. TITLEs 1 - 3 are factory-assigned the defaults for the AJSPX800P; TITLE 4 is assigned the parameter for FILMLIKE. To change the settings, go to the <SCENE> screen from the FILE page. 7 8 Turn the JOG dial button to move the cursor to YES. This writes the setting data into the scene file area of the AJ-D200P internal memory. To exit the menu, press the MENU button. To write settings data for scene files: 1 2 3 Navigate the menu to the SCENE screen. Turn the JOG dial button to move the cursor to the SCENE SEL option. Press the JOG dial button to blink scene file numbers. Then, turn the dial button to select a desired scene file number. 4 5 Press the JOG dial button to accept the scene file. Turn the JOG dial button to return the cursor to the option WRITE. If an SD card is inserted or removed with the <SD CARD READ/ WRITE> screen open, the data title cannot be edited. 4-10-6 Lens File Data The AJ-D200P is capable of correcting the lens white shading. This lens white shading correction may be stored as lens file data (maximum number of data sets is eight). Lens file data allows you to quickly perform a proper white shading adjustment, even when the lens is replaced. For more information on reading/writing data, see [5-3 Mounting the lens and Performing the Flange Back and White Shading Adjustments]. 62 Chapter 5 Preparation 5-1 Power Supply <For your information> The Anton/Bauer battery holder includes both a power supply output connector for lighting and a lighting control switch, which are convenient when attaching a light. Please contact Anton/ Bauer for information about the lighting system. A battery pack or AC power can be used as the power supply for the camera-recorder. Using a Battery Pack Battery packs from the following manufacturers can be used: · Panasonic · Anton/Bauer · IDX · PACO · Sony 2 Insert the battery and slide it in the direction of the arrow. 5 <Notes> Other batteries may be used by changing the menu setting, but system compatibility is not guaranteed. Charge the battery pack with the battery charger before using it. (Please refer to the battery charger's instruction manual for information about charging. ) Release lever <For your information> Removing the battery pack Completely push down and hold the release lever on the battery holder. Then, slide the battery pack in the opposite direction to the arrow while holding the lever down. 3 5-1-1 Mounting the battery and setting the battery type Setting the battery type. Select the battery type listed under BATTERY SELECT. Select BATTERY SELECT from the <BATTERY/P2CARD> screen in the MAIN OPERATION page. [. . . ] Recording/playback time: Approximately 8 minutes: When recorded in DVCPRO format using one AJP2C002SG card with audio signals recorded on 2 channels. <Note> This recording time represents one shot continuously recorded on a P2 card. The recording time may be shorter, depending on the number of shots recorded. [Camera Unit] Pickup devices: 2/3-inch, 520, 000 pixels IT CCD 3. CC/ND Filters: 1: 3200K 2: 5600K + 1/8ND 3: 5600K 4: 5600K + 1/64ND Quantizing: 14-bit linear/18 MHz Digital signal processing: 36 MHz Horizontal drive frequency: 18 MHz Programmable gain: Three positions (L/M/H) can be set by selecting from ­3, 0, +3, +6, +9, +12, +15, +18, +21, +24, +27 or +30 dB. [. . . ]