User manual PANASONIC AJ-D200P

[. . . ] This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION: To reduce the risk of fire or shock hazard and annoying interference, use the recommended accessories only. CAUTION: Do not install or place this unit in a bookcase, built in cabinet or in another confined space in order to keep well ventilated condition. [. . . ] While holding down the STAND BY button, press the REW or FF button, and select USER1. Turn the search dial and move the cursor ( * ) on the menu screen to setup item No. SETUP-MENU MENU <USER1> NO. A00 - 0000 803 TELETEXT DET AUTO A00 LOAD USER2 * A01 SAVE USER2 A02 P. ON LOAD OFF END 4 While holding down the search button, turn the search dial and select the user file into which the USER1 contents are to be saved. User files which have been set to the lock mode are not displayed. When all the user files have been set to the lock mode, the "LOCKED" display appears and the contents cannot be saved. The following messages appear on the menu screen and counter display. Menu screen SETUP-MENU SAVE USER1 USER2 OK?YES<PLAY>/NO<STOP> Counter display TCR 00:00:00:00 SETUP SAVE U-1 U-2 5 The user file number selected in step 4 is displayed in the shaded area. 6 7 8 Press the PLAY button. The contents of the USER1 file are saved in the user file which was selected in step 4 and stored in the memory. When the STOP button is pressed, the USER1 menu display appears while the settings remain unchanged. Turn the search dial and move the cursor ( * ) on the menu screen to any setup item except No. When setting this item, the DISPLAY SEL status is output to VIDEO OUT 3 even if SUPER OFF has been set. However, when the menu is exited, operation complies with the SUPER OFF/ON setting. Also, CHARA TYPE is output to VIDEO OUT 3 according to the status set in the menu. When the DISPLAY SEL setting causes characters to extend beyond the edges of the screen, the setting value is changed so that the characters are automatically displayed in a position on the screen. This sets the position of the characters on the vertical plane for the time code and other super displays output to the VIDEO OUT 3 connector. When setting this item, the DISPLAY SEL status is output to VIDEO OUT 3 even if SUPER OFF has been set. However, when the menu is exited, operation complies with the SUPER OFF/ON setting. Also, CHARA TYPE is output to VIDEO OUT 3 according to the status set in the menu. When the DISPLAY SEL setting causes characters to extend beyond the edges of the screen, the setting value is changed so that the characters are automatically displayed in a position on the screen. This is used to select what is to appear as the time code or other superimposed display at the VIDEO OUT 3 connector. 0: Time only 1: Time and operating status 2: Time, operating status and mode 3: Time and recording time 4: Time and recording date (year/month/day) 5: Time and recording date (month/day/year) 6: Time and recording date (day/month/year) <Notes> · "DVCPRO MODE, " "DV MODE" or "DVCAM MODE" is displayed as the mode when a DVCPRO, DV or DVCAM format tape is used, respectively. [. . . ] 1 2 3 Signal FRAME GROUND TRANSMIT A RECEIVE B Pin No. 4 5 6 Signal RECEIVE COMMON ------ ---- TRANSMIT COMMON Pin No. 7 8 9 Signal TRANSMIT B RECEIVE A FRAME GROUND REMOTE OUT Pin No. 1 2 3 Signal FRAME GROUND RECEIVE A TRANSMIT B Pin No. [. . . ]