User manual PANASONIC AJ-D210P

[. . . ] This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION: Do not install or place this unit in a bookcase, built-in cabinet or in another confined space in order to keep well ventilated condition. [. . . ] <Note> Pressing the MODE button while setup menu item No. 623 (SET UP 50) is selected displays a submenu. While in this status, steps 4 , 5 and 6 can be performed. To return to the item menu, press the MODE button while holding down the PAGE button. Press the DATA+ button or DATA­ button to change the setting. Press the SET button to enter the setting. To change more than one menu item, repeat steps 4, 5 and 6 for each item. <Note> The setting can be canceled by pressing the MODE button. When other items are to be changed without the setting having been entered, press the MODE button and then proceed with steps 4, 5 and 6. 1 Set the LOCAL/MENU/REMOTE switch to the MENU position. The unit is now set to the menu setting mode, and the menu screen appears on the video monitor. SET­UP MENU 00 000 100 200 400 500 600 700 MAIN NO. 00 5 6 SYSTEM BASIC OPERATION INTERFACE TAPE PROTECT TIME CODE VIDEO AUDIO 7 In the menu setting mode, the REW, STOP, FF, SEARCH, PLAY, PAUSE/STILL and REC function buttons serve as the PAGE, MENU DOWN, MENU UP, MODE, DATA­, DATA+ and SET buttons. Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position. Perform steps 2 through 6 of "Setting method using on-screen menus, " and change the items to the desired settings. (See page 23) NO YES 7 Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position. This completes the menu settings. 24 Setup (Initial Settings) How to load the user defaults How to protect the menus Opening the setup menu can be prevented even when the LOCAL/MENU/REMOTE switch on the front panel is set to the MENU position by setting the unit to the menu protect mode. 1 2 Set the LOCAL/MENU/REMOTE switch to the MENU position. The unit is now set to the menu setting mode, and the menu screen appears on the video monitor. The unit is set to the default setting mode, and the default setting screen appears on the video monitor. SELECT 0 1 2 3 MODE ESCAPE LOAD SAVE PROTECT 1 2 Set the LOCAL/MENU/REMOTE switch to the MENU position. The unit is now set to the menu setting mode, and the menu screen appears on the video monitor. The unit is set to the default setting mode, and the default setting screen appears on the video monitor. SELECT 0 1 2 3 MODE ESCAPE LOAD SAVE PROTECT 3 Press the MENU-UP button or MENU-DOWN button to move the cursor to the LOAD position, and press the SET button. The unit is set to the LOAD mode, and the load screen appears on the video monitor. SET­UP MENU <LOAD> NO FACTORY (ALL) FACTORY (NOT SYSTEM) USER (ALL) USER (NOT SYSTEM) 3 Press the MENU-UP button or MENU-DOWN button to move the cursor to the PROTECT position, and press the SET button. [. . . ] This appears when there is a problem with the supply voltage. This appears when the input DC voltage has dropped below the undercut voltage (approx. 10. 6V). E -- 00 E -- 01 E -- 02 E -- 09 E -- 67 E -- 10 E -- 68 E -- 69 E -- 11 E -- 6A E -- 6B E -- 21 E -- 80 E -- bA 38 Emergency Eject Procedure for removing the tape manually in an emergency Use the procedure below to remove the cassette tape if it can not be removed even when the EJECT button is pressed. OBefore proceeding to eject the tape manually, you must first turn off the power to the unit. [. . . ]