User manual PANASONIC AJ-D230H

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. $ THIS APPARATUS MUST BE EARTHED To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. [. . . ] To change another item without entering the setting, press the MODE button and then repeat steps 4, 5 and 6. 00 000 100 200 400 500 600 700 A00 SYSTEM BASIC OPERATION INTERFACE TAPE PROTECT TIME CODE VIDEO AUDIO MENU 7 Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position. This completes the menu settings. How to return to the factory settings In the menu setting mode, the REW, STOP, FF, SEARCH, PLAY, PAUSE/STILL and REC control buttons function as the PAGE, MENU-DOWN, MENU-UP, MODE, DATA­, DATA+ and SET buttons, respectively. 1 2 Set the LOCAL/MENU/REMOTE switch to the MENU position. The VTR is set to the menu setting mode, and the menu screen is displayed on the video monitor. 2 3 Press the MENU-UP button or MENU-DOWN button to move the cursor (2) to the first menu item to be changed. Press the MODE button, and select the setting for each item. To return to the menu screen, press the MODE button while holding down the PAGE button. Press the RESET button. The VTR is set to the default setting mode, and the default setting screen is displayed on the video monitor. SELECT MODE 2 0 ESCAPE 1 LOAD 2 SAVE 3 PROTECT 20 Setup (Initial Settings) 3 Press the MENU-UP button or MENU-DOWN button to move the cursor to the LOAD position, and press the SET button. The VTR is set to the LOAD mode, and the LOAD screen is displayed on the video monitor. SET­UP MENU <LOAD> 2 NO FACTORY USER (ALL) USER (NOT SYSTEM) 4 Press the MENU-UP button or MENU-DOWN button to move the cursor to the SAVE position, and press the SET button. The VTR is set to the SAVE mode, and the SAVE screen is displayed on the video monitor. SET­UP MENU <SAVE> 2 NO USER (ALL) USER (NOT SYSTEM) 4 Press the MENU-UP button or MENU-DOWN button to move the cursor to FACTORY, and press the SET button. O If the cursor is moved to USER (NOT SYSTEM) and this operation is performed, operations are performed using the user settings stored in the memory for all the menus with the exception of the SYSTEM menu. O If the cursor is moved to NO and this operation is performed, operation returns to the menu screen while the user settings stored in the memory remain unchanged. Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position. This completes the menu settings. 4 Press the MENU-UP button or MENU-DOWN button to move the cursor to YES, and press the SET button. The menu screen now appears. 5 22 Setup (Initial Settings) 5 Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position. The unit is now set to the menu protection mode. When the LOCAL/MENU/REMOTE switch is set to the MENU position, the VTR is not set to the menu setting mode, and "MENU PROTECTED" appears on the video monitor screen. <Notes> If, while the menu protection mode is being set, the LOCAL/MENU/REMOTE switch is set to the MENU position while the COUNTER button on the front panel is pressed, the unit is set to the menu setting mode, and regular menu settings can be performed. Perform steps 2 through 7 of "How to perform settings using the on-screen menu. " How to display the DIAG menu This unit comes with a function for displaying the "HOURS METER, " software "VERSION" and the deck's serial number on the video monitor. 1 Set the LOCAL/MENU/REMOTE switch to the MENU position while pressing the EJECT button. The unit is set to the DIAG display mode, and the hours meter and deck's serial number are displayed on the video monitor. DIAG­MENU HOURS METER Ser 222222222 H00 OPERATION 00000H H01 DRUM RUN 00000H H02 TAPE RUN 00000H H03 THREADING 00000T H11 DRUM RUN r 00000H H12 TAPE RUN r 00000H H13 THREADING r 00000T END Items with "r" can be reset when servicing is performed. How to release the menu protection 1 2 Set the LOCAL/MENU/REMOTE switch to the MENU position while pressing the COUNTER button on the front panel. [. . . ] BATTERY This appears when the input DC voltage has dropped below the lower voltage limit (approx. 10. 6 V). ­­d­­ E ­ 57 E ­ 00 E ­ 59 E ­ 60 E ­ 01 E ­ 61 E ­ 02 E ­ 64 E ­ 67 E ­ 09 E ­ 69 E ­ 10 E ­ 6A E ­ 29 E ­ 6B E ­ 31 E ­ 70 E ­ 71 E ­ 51 E ­ 72 E ­ 73 E ­ 52 E ­ bA E ­ 53 36 Emergency Eject CAUTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Procedure for removing the tape manually in an emergency Use the procedure below to remove the cassette tape if it can not be removed even when the EJECT button is pressed. OBefore proceeding to eject the tape manually, you must first turn off the power to the unit. [. . . ]