User manual PANASONIC AJ-D455

[. . . ] Digital Video Cassette Recorder AJP Operating Instructions Printed in Japan VQT9172 S0401H D P IMPORTANT "Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws. " CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: To reduce the risk of fire or shock hazard, do not expose this equipment to rain or moisture. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER MOUNTING OF THE OPTIONAL INTERFACE BOARD TO AUTHORIZED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. [. . . ] 1: Recording on the cassette tape is prohibited. In this case, the REC INH lamp on the front panel lights. For selecting whether the REC INHIBIT lamp is to flash or light when the cassette has been set to the accidental erasure prevention status. <Note> When ON has been selected as the setup menu item No. 114 (REC INHIBIT) setting, the REC INHIBIT lamp will light all the time regardless of what has been selected as this item's setting. For selecting whether to enable or disable the operation of the front panel's EJECT button. 0: The button's operation is disabled in the recording mode. 1: The button's operation is enabled in all modes. 114 REC INHIBIT 0000 0001 OFF ON 120 REC INH LAMP 0000 0001 LIGHT FLASH 121 EJECT SW INH 0000 0001 REC OFF The underline on the setting item denotes the initial setting. 25 Setup menus USER menu <INTERFACE> Item No. 0000 0001 Setting Superimposed display OFF ON Description This selects whether the 9-Pin connector functions when the REMOTE/LOCAL switch has been set to REMOTE. 0: Do not function 1: Function This selects the ID information which is returned to the controller. 0: 20 25H 1: DVCPRO's, own ID is returned (F0 33H). 2: The unit's own ID (A0 3CH) is returned. <Note> Set "ORIG" only when the unit is connected with a Panasonic controller (such as the AJ-A900, optional accessory). These settings are for selecting whether the RS-232C connector is to function when the REMOTE/LOCAL switch is set to REMOTE. These settings are for selecting the RS-232C communication speed (baud rate). 202 ID SEL 0000 0001 0002 OTHER DVCPRO ORIG 204 RS232C SEL 0000 0001 OFF ON 205 BAUD RATE 0000 0001 0002 0003 0004 0005 0000 0001 0000 0001 0000 0001 0002 300 600 1200 2400 4800 9600 7 8 1 2 NON ODD EVEN 206 207 208 DATA LENGTH STOP BIT PARITY These settings are for selecting the RS-232C data length. (Unit: bit) These settings are for selecting the RS-232C stop bit length. (Unit: bit) These settings are for selecting the none, odd or even for the RS-232C parity bit. 1: An odd number of bits is used for the parity system. 2: An even number of bits is used for the parity system. These settings are for selecting whether the ACK code is to be returned when a command is received from RS-232C. 1: ACK code is returned. 209 RETURN ACK 0000 0001 OFF ON The underline on the setting item denotes the initial setting. 26 USER menu <EDIT> Item No. 303 Superimposed display STD/ NON-STD No. [. . . ] <Notes> 1) The drum rotates as soon as condensation is detected when the unit is in EJECT mode. 2) When condensation is detected while a cassette tape is inserted, drum rotation stops, the cassette tape is ejected and the drum rotation begins again. If any other number appears frequently, ask your dealer to inspect the unit. VTR operation (VTR measures) E-20 DEW EJECT Any other number 47 Connector signals VIDEO IN SERIAL IN (DIGITAL) Y, PB, PR (ANALOG) VIDEO IN REF VIDEO IN S1-VIDEO IN BNC × 2 BNC × 3 BNC × 2 BNC × 2 4-pin × 1 Loop-through, 75 termination switch provided Loop-through, 75 termination switch provided Active through (Option) VIDEO OUT SERIAL OUT(DIGITAL) BNC × 3 Y, PB, PR (ANALOG) VIDEO OUT S1-VIDEO OUT BNC × 3 BNC × 3 4-pin × 1 (Option) AUDIO IN SERIAL IN (DIGITAL) AUDIO IN (DIGITAL) AUDIO IN (ANALOG) TIME CODE IN BNC × 2 BNC × 1 XLR × 2 BNC × 1 Active through (Option) CH1/CH2 AES/EBU format CH1, CH2 Pin No. [. . . ]