User manual PANASONIC AJ-D640P

[. . . ] · AVC-Intra capability is available when the optional AVC-Intra Codec board AJ-YBX200G is installed to the unit. S1106S2077 -P D Printed in Japan ENGLISH VQT1B57-2 Read this first! For AJ-D640PP THIS EQUIPMENT MUST BE GROUNDED To ensure safe operation, the three-pin plug must be inserted only into a standard three-pin power outlet which is effectively grounded through normal household wiring. Extension cords used with the equipment must have three cores and be correctly wired to provide connection to the ground. Wrongly wired extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power outlet is grounded or that the installation is completely safe. [. . . ] Then hold down the OUT button and press the ENTRY button. Using Play List 6 Press the EVENT button to end the change operation. NOTE: · Steps 4 and 5 can be handled as alternatives, you do not have to carry out both steps. · If the new IN point comes after an already registered OUT point, the existing OUT point will be reset. A return to the play list screen will show that the OUT point has automatically been changed to the end of the clip. · If the new OUT point comes before an already registered IN point, a return to the play list will show that the IN point of that clip has automatically been changed and registered at the beginning of the clip. · An event with a voice-over cannot be modified. Delete the voiceover before modifying the event. · The changed content will be neglected if the unit is turned off during change of an event from video. 2 4 5 4, 5 1 Open the play list screen. 3 Press the EVENT button. This activates the event edit mode. Trimming Events You can change IN and OUT points for events in frame increments (in 4-frame increments at 24PN). 3 Use the cursor buttons to change the IN point. Hold down the IN button and press the TRIM+ button or the TRIM­ button. The IN point is incremented or decremented in frame increments (in 4-frame increments at 24PN). 1 Press the ENTRY button to finalize. 4 Change the OUT point. Hold down the OUT button and press the TRIM+ button or the TRIM­ button. The OUT point is incremented or decremented in frame increments (in 4-frame increments at 24PN). Press the ENTRY button to finalize. 5 Change the SPLIT point 2 3 3, 4, 5 4 5 Hold down the SPLIT button and press the TRIM+ or the TRIM­ button. 5 Select [YES] in the delete confirmation screen and press the SET button. This deletes all play list events. NOTE: · To quickly select successive lines, hold down the SHIFT button and press the SET button (MULTI SEL) to select all events from the previous time the SET button was pressed and up to the cursor location where the MULTI SEL button was pressed. · To cancel a selection Place the cursor on a selected event and press the SET button to cancel the selection. · To cancel all selections Hold down the SHIFT button and press the EXIT button (CANCEL) to cancel all selected lines. 3 Press the MENU button. 4 Use the cursor buttons to choose [OPERATION] ­ [DELETE SELECTED EVENT]. 5 Press the SET button. 6 Select [YES] in the delete confirmation screen and press the SET button. This deletes all selected events. NOTE: · You can also delete a selected event in step 3 by holding down the SHIFT button and pressing the INSERT button (DELETE). Using Play List: Editing Play Lists 77 Saving Events While editing a loaded play list file or the play list file has been saved using [FILE] ­ [SAVE AS], the file can subsequently be saved using the following procedure. Use [SAVE AS] for the first save operation. 1 Open the play list screen. 3 Use the cursor buttons to choose [FILE] ­ [SAVE]. 5 Select [YES] in the confirmation screen and press the SET button. This saves the play list. 78 Using Play List: Editing Play Lists Overwrite Editing of Play Lists When an event is registered, an event can be overwritten on video and audio, or on EXTRA track. Overwrite editing is performed by specifying the IN and OUT points of the event that will be overwritten (recorder side) and the event that will overwrite it (player side). Switching channels and audio level adjustments are available in an overwrite edit. P IN R IN R OUT 2 Source VIDEO AUDIO 1234 EXTRA 1234 1 1 Events that are overwritten (recorder) IN point: R IN OUT point: R OUT Overwrite events (source/player) IN point: P IN OUT point: P OUT Using Play List R IN VIDEO AUDIO 1234 EXTRA 1234 R OUT R IN R OUT R IN R OUT 2 2 1 1 VIDEO AUDIO 1234 EXTRA 1234 1 1 2 VIDEO AUDIO 1234 EXTRA 1234 2 2 2 1 1 Video of event 2 overwrites video of event 1 Audio of event 2 overwrites audio of event 1 Audio and video of event 2 overwrites audio and video of event 1 NOTE: This edit function uses the play list as a recorder. In the overwrite mode, press the INSERT button and locate video and audio for overwriting from clips that match the play list format. [. . . ] In copying, be sure to copy both the CONTENTS folder and the LASTCLIP. TXT file together. · When transferring data from multiple P2 cards, create separate folders for each P2 card to prevent overwriting clips with identical names. · Do not delete data on a P2 card. · Be sure to use a P2 device or the P2 Viewer to format P2 cards. Drive: \ CONTENTS AUDIO CLIP ICON PROXY VIDEO VOICE LASTCLIP. TXT* All these folders are required. [. . . ]