User manual PANASONIC AJ-D650P

[. . . ] This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning: To assure continued FCC emission limit compliance, the user must use only shielded interface cables when connecting to external units. Also, any unauthorized changes or modifications to this equipment could void the user's authority to operate it. WARNING: RB OTO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. [. . . ] to move the arrow (cursor) the <CMCR RA/RT > A AD EDWIE SLC EET : 1 RA ED SLC EET : 1 RT n WIE CR CNI AD OFG TTERA IL ED RA UE DT ED SR AA T T E 22222222 IL: 1 : 5 : 2 : 6 : 3 : 7 : 4 : 8 : To save the VTR unit's data, open the VTR CARD READ/WRITE screen, and perform steps 11 to 13. If one of the following messages appears when the JOG dial button is pressed, the data cannot be saved. Error message Remedial action Insert the card. WRITE NG NO CARD (SD memory card has not been inserted) WRITE NG FORMAT ERROR (formatting error) WRITE NG ERROR (the data cannot be saved) The card was formatted by a device other than the unit. Replace it. 14 Press the MENU operations. button to exit the menu The setting menu is cleared, and the displays showing the unit's current statuses appear at the top and bottom of the viewfinder screen. 77 SD memory card operations (continued) Loading the data saved on the card operations (pages 86 to 88), 1 Perform the menu "CAM CARD READ/WRITE" and display the screen. A AD EDWIE n< C M C R R A / R T > SLC EET : 1 RA ED SLC EET : 1 WIE RT CR CNI AD OFG TTERA IL ED RA UE DT ED SR AA TTE IL: 1 : 2 : 3 : 4 : n Load the data of the selected file. to move the arrow (cursor) to the <CMCR RA/RT > A AD EDWIE SLC EET : 1 RA ED SLC EET : 1 WIE RT CR CNI AD OFG TTERA IL ED RA UE DT ED SR AA TTE IL: 1 : 2 : 3 : 4 : 5 : 6 : 7 : 8 : 5 : 6 : 7 : 8 : If the data is given a title when it is saved, the title will also be displayed. <Note> "F_" appears in front of a title which was set in the film mode; "V_" appears in front of a title which was set in the video mode. When the data has been loaded, the unit is set to the operation mode of the loaded data. JOG dial 5 When theappears. button is pressed, the following message <CMCR RA/RT > A AD EDWIE RA ED SLC EET : 1 WIE RT SLC EET : 1 CR CNI AD OFG RA UE DT ED SR AA TTE IL RA ?dial button arrow 2 Turn thetoJOGSELECT item to move the avove (cursor) the which comes READ, and press the JOG dial button. <CMCR RA/RT > A AD EDWIE EET : 1 n SLC RA ED SLC EET : 1 WIE RT CR CNI AD OFG TTERA IL ED RA UE DT ED SR AA TTE IL: 1 : 2 : 3 : 4 : dial button the arrow 6 Turn the JOG and press theto move button. (cursor) to YES, JOG dial When the data loading is completed, the following message appears. <CMCR RA/RT > A AD EDWIE RA ED SLC EET : 1 WIE RT SLC EET : 1 CR CNI AD OFG RA UE DT ED SR AA TTE IL RA O ED K YS E N O TTE IL 22222222 : : 5 : 6 : 7 : 8 : n JOG to 3 Turn 1the 8, anddial buttonJOG select any number from to press the dial button. To load the VTR unit's data, open the VTR CARD READ/WRITE screen, and perform steps 4 to 6. 78 SD memory card operations (continued) If one of the following messages appears when the JOG dial button is pressed, the data cannot be loaded. Error message Remedial action READ NG Insert the card. (2) Press the AUTO W/B BAL switch to the ABB position and adjust the black balance. (3) Press the AUTO W/B BAL switch to the AWB position and adjust the white balance again. For details on how to adjust the white balance, refer to "Adjusting the white balance and black balance" (pages 53 to 56). at the subject, and adjust the focus is to 3 When the electronic shuttermode. be used, set the shutter speed and operating O For details, refer to "Setting the electronic shutter" (pages 57 to 59). 3 2 4, 5 1-2 1-1, 1-2 4 Press the VTR START button or lens VTR button to start recording. During recording, the REC lamp inside the viewfinder lights. 5 To stop the recording, press the VTR START button again. The REC lamp inside the viewfinder goes off. 82 Recording (continued) Scene-to-scene continuity If the unit is in the rec-pause mode, it is possible to ensure scene-to-scene continuity with an accuracy of 0 up to 1 frame just by pressing the VTR START button or lens VTR button. If the unit is in a mode other than rec-pause, the point at which the scene-to-scene continuity is to be maintained must be located before recording is started. Ensuring scene-to-scene continuity at other times Proceed as follows either after the tape has been allowed to run or after the cassette has been ejected or when ensuring continuity on a tape which has been recorded only in part. viewfinder 1 While monitoring the to play backscreen, press the PLAY/PAUSE button the tape. tape where continuity 2 At the place on the the PLAY/PAUSE (or is to be maintained, press STOP) button again to stop the tape. 3 Press the lens images are shown, but two or so No playback seconds later preparations are made for shooting with scene-to-scene continuity. To check whether the tape has been cued up to the place where shooting with scene-to-scene continuity is to start, press the RET button again. During rec-pause The scene-to-scene continuity timing is located automatically. However, the time taken until the start of recording differs depending on the setting of the VTR SAVE/STBY switch. O When the VTR SAVE/STBY switch is set to SAVE, recording commences about two seconds after the VTR START button is pressed. [. . . ] 2 Set the AUDIO SELECT CH1 and CH2 switch to MAN. level displays increase. 6. Inspections relating to the time code and user bits AUDIO LEVEL CH1 and CH2 controls. 3 Turn thethat when they are turned clockwise, the 1 Set the user bits as required. procedure, refer to For details on the setting Check "Setting the user bits" (page 65). 4. [. . . ]