User manual PANASONIC AJ-D700P

[. . . ] FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] 0001 MODE1 : The dial ring lights during search (JOG/SLOW/SHTL) mode. 0002 MODE2 : The dial ring lights during JOG mode. 0003 MODE3 : The dial ring lights when a cassette is inserted. The underlined items indicates the initial setting. 38 Setup menus USER menu No. /Item 200 PARA RUN 0000 DIS : No operation in synchronization 0001 ENA : Operation in synchronization <Note> When operating two or more VTRs in synchronization, set all the VTRs to ENA. 201 9P SEL This selects whether the REMOTE (9P) connector functions when the CONTROL switch has been set to REMOTE. 209 0000 0001 202 ID SEL 0000 OTHER 0001 DVCPRO 0002 ORIG <Notes> OID information of any VTR except for the DVCPRO's is set in OTHER. OThe ORIG setting should only be used when a Panasonic controller (AG-A850 etc. 203 25P SEL This selects whether the PARALLEL (25P) connector functions when the CONTROL switch has been set to REMOTE. 0000 0001 204 RS232C SEL OFF : Connector does not function. 210 25P STBY CMD OFF : Connector does not function. RETURN ACK <INTERFACE> Description No. /Item 208 PARITY 0000 NON : Parity bit is not used. 0001 ODD: An odd number of bits is used for the parity system. 0001 CH1 : Compliance with analog CH1 edit preset. 0002 CH2 : Compliance with analog CH2 edit preset. 0003 CH1+2 : Compliance with either analog CH1 or CH2 edit preset. 310 CONFI EDIT 0000 OFF : No simultaneous playback 0001 ON : Simultaneous playback <Note> Simultaneous playback is valid when the MODE switch is set to TAPE. This selects whether to conduct simultaneous playback while editing is in progress. This selects the operation to be performed when an edit point has been set incorrectly (when the OUT point is before the IN point). 0000 MANU : Editing is not executed unless the illegal edit point is cleared or set again properly. 0001 AUTO : The edit points already input are automatically cleared. 303 STD/ NON-STD This selects STD or NON-STD in accordance with the composite input signal. 0000 AUTO : Standard/non-standard signals are automatically identified and processed. 0001 STD : Standard signals are processed. (Forced STD) 0002 N-STD : Non-standard signals are processed. (Forced NON-STD) <Note> Use the non-standard (N-STD) setting when video or audio trouble occurs with signals from laser discs or a satellite. [. . . ] data = AJ-D700PP 72 SDTI interface Digital data input/output operations using the SDTI format (compressed digital interface) are enabled by installing the AJ-YAC930G SDTI board (optional accessory) in this unit. <Notes> SDTI (Serial Data Transport Interface) complies with the SMPTE 305M standard. The data stream format transferred via the SDTI complies with the SMPTE 321M standard. SIGNAL GND Reference signal generator Source AES/EBU AC IN CH1/2 IN ANALOG VIDEO IN ON REMOTE REMOTE IN/OUT 75 OFF ANALOG OPTION 1 CH1 PUSH AUDIO PUSH CH2 IN PUSH TC IN IN SDI OUT 1 Y REMOTE CH1/2 OUT PB OUT TC OUT ACTIVE THROUGH REF VIDEO IN ON 2 ENCODER REMOTE PR OFF 75 CH1 RS-232C AUDIO OUT CH2 MON L (SUPER) 3 OPTION 2 Y 1 VIDEO OUT SDTI PARALLEL IN MON R OUT 1 PB (WFM) 2 PR (SUPER) 3 2 Precautions to observe when using the SDTI signals O The unit can record only if the SDTI input signals are 1a transfer signals in the DVCPRO format. However, when playback signals other than normal 1a playback signals have been input, there is no guaranty for the pictures and sound recorded or for pictures and sound with EE. [. . . ]