User manual PANASONIC AJ-D810K

[. . . ] Be sure to turn off the power prior to opening the unit, before changing the position of any switch, and especially before removing or reinserting any circuit board. WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS-USE AND STORE ONLY IN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DROPPING OR SPLASHING LIQUIDS, AND DO NOT PLACE ANY LIQUID CONTAINERS ON TOP OF THE EQUIPMENT. CAUTION: Do not install or place this unit in a bookcase, built-in cabinet or in another confined space in order to keep well ventilation condition. Ensure that curtains and any other materials do not obstruct the ventilation condition to prevent risk of electric shock or fire hazard due to overheating. THIS APPARATUS MUST BE GROUNDED To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power outlet (socket) which is effectively grounded through normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to the ground. [. . . ] Enter the cue point with the number keys. 0 0 0 7 4 0 4 4 Cue points also can be entered by pressing the ENTRY button. In this case, the time data of the current tape position will be entered. CUE TIME ENTRY S 00 (4) Press the ENT key. The cursor will disappear. H 44 M 07 04 F (5) Press the PREROLL button. PREROLL When the PREROLL button is pressed, cue-up operation will start, and the tape will stop at the preroll point (the point preceding the cue point by the preroll time). To stop at the cue point, either set the preroll time to "0" or press the F key and PREROLL button together. (This results in the cue-up operation. ) *The STANDARD mode is set using the F9 key on the PANEL SET UP menu. (This key can be set in either the STANDARD or REVERSE mode. ) ­ 32 ­ Basic operations When TC INPUT is set to the REVERSE mode* (1) Press the cursor center key to display the cursor. The time code value will be highlighted. Cursor center key LTCR 00 : 00 : 00 : 00 Cursor key Cursor (2) Move the cursor with the cursor key (4) to the CUE TIME display section. The cue display section will be highlighted. CUE TIME H M S F Cursor (3) Press the cursor center key again to change it to a bar cursor. Enter the cue point with the number keys. 4 0 7 0 4 4 Cue points also can be entered by pressing the ENTRY button. For audio V fading, set the F13 (MODE) key on the INSERT (OR ASSEMBLE) MANUAL EDIT SET UP menu to VFADE. The settings for audio cross editing can be performed only when EE1 has been set as the EDIT REC status. How to display the menu: INSERT (or ASSEMBLE) AUTO EDIT SET UP menu: INSERT (or ASSEM )# F8 ­ 37 ­ Automatic insert/assemble editing The following flowchart shows the operation for automatic insert editing or automatic assemble editing with two digital VTRs. Switch on the power to the player and to the recorder. Insert the cassettes required for editing into the VTRs. Press the REMOTE button on the player and set the button to REMOTE (lamp is lit). REMOTE 5. Press the REMOTE button on the recorder and set the button to LOCAL (lamp is not lit). REMOTE 6. Set the F3 (W/PLYR) key on the recorder's INSERT (or ASSEMBLE) AUTO EDIT menu to ON. Set the F1 (P-2) key on the recorder's SET UP INTERFACE menu to MODE-1. Set the RS-422A control mode for each VTR depending on the player/recorder connections. (Refer to the F1 (P-2) key on the SET UP INTERFACE menu. ) P-2 MODE-1 8. Set the F13 (REC INH) key on the recorder's HOME menu to FREE or NRML. REC. REC INH FREE 9. [. . . ] (Bear in mind that continuing to turn the screwdriver even after the cassette has been ejected will cause the gear engagement to fail and/or other problems. ) Loading motor (In this VTR, turn the blades (black) which are provided in front of the pulley. ) C A (S, M) A' (L) B View of inside as seen through hole B Insert the screwdriver here. ­ 51 ­ DIP switch AV microcomputer DIP switch specifications SW6501 1 2 3 4 5 6 7 8 Normal Normal -- -- ON (0) OFF (1) Normal Normal Normal Normal -- -- -- -- Normal Normal Not used Not used Not used Not used Keep this switch at the factory setting. Keep this switch at the factory setting. Keep this switch at the factory setting. Keep this switch at the factory setting. [. . . ]