User manual PANASONIC AJ-D850A

[. . . ] Digital Video Cassette Recorder AJP Operating Instructions IMPORTANT "Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws. " CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: To reduce the risk of fire or shock hazard, do not expose this equipment to rain or moisture. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER MOUNTING OF THE OPTIONAL INTERFACE BOARD TO AUTHORIZED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. [. . . ] The contents of the USER1 file are saved in the user file which was selected in step 4 and stored in the memory. When the STOP button is pressed, the USER1 menu display appears while the settings remain unchanged. Turn the search dial and move the cursor ( * ) on the menu screen to any setup item except No. The USER1 settings are now stored in the memory. If the USER1 settings are not going to be stored in the memory, do not press the SET button but press the MENU button. Automatic loading of user file when the power is turned on When the user file to be loaded is selected in advance using setup menu item No. A02 (P. ON LOAD), it can be automatically loaded into USER1 when the power is turned on. ­ 54 ­ SYSTEM menu <SYSTEM> Item No. 0255 Setting Superimposed display ­127 . 128 Description System phase adjustment: Total variable range: ±180° or more ­: Advanced +: Delayed <Note> If setting operation is performed, the setting value does not return to factory (default) setting. System phase adjustment: SC cycle phase (280 ns steps) ­: Advanced +: Delayed <Note> If setting operation is performed, the setting value does not return to factory (default) setting. Video phase adjustment: 148 ns steps ­: C advanced +: C delayed 01 SYS H 0000 . 123 02 VIDEO PHASE 03 YC COARSE YC timing rough adjustment: 148 ns steps ­: C advanced +: C delayed 04 YC FINE YC timing fine adjustment: 37 ns steps ­: C advanced +: C delayed (The digital OUT option YC does not change. ) SCH phase adjustment: 90° units (The S and C phases change but the H phase does not change. ) SCH phase adjustment: Total variable range: ±45° or more (The S and C phases change but the H phase does not change. ) 05 SCH COARSE 06 SCH FINE 07 PB OUT LV Component PB output level adjustment: Total variable range: ±3 dB 08 PR OUT LV Component PR output level adjustment: Total variable range: ±3 dB The underline on the setting item denotes the initial setting. ­ 55 ­ Setup menus SYSTEM menu <SYSTEM> (continued) Item No. 0255 0000 0001 Setting Superimposed display ­128 . 127 FULL FINE Description This adjusts the audio output phase with respect to the video output: 20. 8 µs steps ­: The audio output phase is advanced with respect to the video output. +: The audio output phase is delayed with respect to the video output. This selects the adjustable range for SYSTEM H during when the ENCODER REMOTE is connected. 0: ±8 µ sec (±30 steps) 1: ­1. 9 to +2. 7 µ sec (­7 to +10 steps) <Note> If setting operation is performed, the setting value does not return to factory (default) setting. System phase adjustment: 4. 48 µs steps 0: ­13. 4 µ sec 1: ­8. 96 µ sec 2: ­4. 48 µ sec 3: 0 sec 4: +4. 48 µ sec 5: +8. 96 µ sec 6: +13. 4 µ sec <Note> Factory settings will remain unchanged even if an attempt is made to perform a setting operation. This selects whether the system file lock mode is to be engaged or released. 0: The lock is released (file data can be changed). 1: The lock is engaged (file data cannot be changed). 20 SYS H RANGE 21 SYS H OFFSET 0000 0001 0002 0003 0004 0005 0006 ­3 ­2 ­1 0 1 2 3 30 MENU LOCK 0000 0001 OFF ON The underline on the setting item denotes the initial setting. ­ 56 ­ USER menu <BASIC> Item No. 000 Superimposed display P-ROLL TIME No. 0011 Setting Superimposed display 0S . [. . . ] 4 5 6 Signal TRANSMIT COMMON ------ ---- RECEIVE COMMON Pin No. 7 8 9 Signal RECEIVE B TRANSMIT A FRAME GROUND ­ 100 ­ PARALLEL REMOTE (25P) Pin No. 1 2 3 4 5 6 7 8 9 Signal PLAY COMMAND STOP COMMAND FF COMMAND REW COMMAND REC COMMAND EJECT COMMAND STAND BY COMMAND PREROLL COMMAND IN SET COMMAND Pin No. 10 11 12 13 14 15 16 17 18 Signal ------ ---- ------ ---- 10V, MAX 300mA PLAY STATUS STOP STATUS FF STATUS REW STATUS REC STATUS EJECT STATUS Pin No. [. . . ]