User manual PANASONIC AJ-D90

[. . . ] 88 LTC output selection when playing back a 25P (23. 98P/24P) tape with a 23. 98/24 (25) Hz VTR system added . 98 INSERT/ASSEMBLE MANUAL EDIT SET UP menu . 115 INSERT/ASSEMBLE AUTO EDIT SET UP menu . 117 The underlining of functional description with each menu denotes the initial setting. ­2­ Contents SET UP menu . [. . . ] Valid when the F13 key is set to X FADE or V FADE. The times that can be set are as follows: 5, 10, 15, 20, 25, 50, 100 ms. (Initial setting is 5 ms. ) For the setting procedure, refer to "Selecting the audio fade time" (on page 107). Audio editing can be accomplished while cross-fade editing prior playback audio and input audio or V-fade editing. X FADE: Performs audio cross-fade editing. V FADE: Performs audio V-fade editing. F12 FD TIME° For setting the audio fade time. F13 MODE° For setting the audio fade edit. °Only CUT can be selected when TAPE has been selected as the EDIT REC STATE setting. However, FADE can be selected by pressing this key and F key together, in which case the EDIT REC STATE setting is switched to EE1. ­ 102 ­ INSERT/ASSEMBLE MANUAL EDIT SET UP menu EDIT REC INHIBIT mode display This display shows the statuses of the editing inhibit modes. SOFTWARE The editing inhibit modes selected for each channel are shown here. Refer to "Selecting the SOFTWARE inhibit channels. " VIDEO: Video channel editing is inhibited. CH1­CH8 (CH4): Digital audio channel editing is inhibited. TC: Time code channel editing is inhibited. (3) Optimizing is initiated by pressing the PLAY and STAND BY buttons together. ONotesN (1) The optimized tracking value is retained even when the VTR is transferred to another menu. (2) The following message appears while the tracking is being optimized, and the mark that indicates the tracking value appears to show the progress made in the processing. OPTIMIZING Upon completion of the optimizing, the following message appears, the TRACK OPT appears on the INSERT/ASSEMBLE MANUAL EDIT and HOME menu screens. COMPLETE ­ 105 ­ INSERT/ASSEMBLE MANUAL EDIT SET UP menu (3) The following message appears and optimizing is suspended in the following cases: When the VTR is set to a mode other than PLAY while optimizing is underway. When no video signals have been recorded on the tape. When no CTL signals have been recorded on the tape. NOT COMPLETE At times like these, the center value (0) is set as the optimized value. (4) If the optimizing processing fails to be completed even after 5 seconds, the following message appears and optimizing is suspended. TIME OVER (5) When the cassette is ejected, the optimized value is canceled. Manually adjusting the tracking (1) Insert the tape, and play it back. (2) Press the F10 (TRACKING) key and set it to VAR. TRACKING VAR (3) Turn the ADJUST control, and adjust it so that the envelope level is set to its maximum. ADJUST RCEV EN 5 4 3 2 1 ­ 106 ­ INSERT/ASSEMBLE MANUAL EDIT SET UP menu Selecting the audio fade time (1) Press the F13 (MODE) key to set it to X FADE or V FADE. MODE X FADE (2) Press the F12 (FD TIME) key. FD TIME 10 (3) Turn the ADJUST control to select the audio fade time. ADJUST 25 V FADE Advance playback signals V X X FADE Insert signals V X V FADE Advance playback signals Fade time OUT point The solid lines indicate X fading. [. . . ] The message is automatically cleared after it has been displayed for several seconds. F13 F12 F11 F10 F9 F1 F2 F3 F4 F5 F6 F7 F8 ­ 190 ­ Operation messages (in AUTO EDIT mode) No. 350 351 352 353 Message NO CASSETTE NO PRESET NO IN POINT NO PLY' R MODE Description of error/problem A cassette tape has not been inserted. The editing channel has not been selected in the editing mode or during insert editing. The edit point data required for editing has not been entered. [. . . ]