User manual PANASONIC AJ-DE77H

[. . . ] Incorrectly wired extension cords can be extremely hazardous. The fact that the equipment operates satisfactorily does not imply that it is grounded, and the installation is not necessarily safe. For your safety, if in any doubt about the effective grounding of the equipment or power outlet (socket), please consult a qualified electrician. CAUTION: Do not install or place this unit in a bookcase, built-in cabinet or any other confined space in order to maintain adequate ventilation. Ensure that curtains and any other materials do not obstruct the ventilation to prevent risk of electric shock or fire hazard due to overheating. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. CAUTION: CAUTION: THE AC OUTLET (MAINS SOCKET) SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. [. . . ] All the registered item names and registered values are now set to the factory settings. (These settings cannot be restored. ) Special IN menu list No. SUPER DISPLAY Description of setting 2. Entering the 50-pin connector pins Press the ADJ dial. The entered 50-pin connector pin display is highlighted. Functions not featured on the setup menua B00 STBY ON B01 STBY OFF B02 STBY ONOFF B03 EJECT B04 CUE For transferring to the STANDBY ON mode. For transferring to the STANDBY OFF mode. For alternately transferring to the STANDBY ON and OFF mode. For prerolling the tape to the IN point when the IN point has been registered; for prerolling the tape to the current point when the IN point has not been registered. For transferring to the still picture (STILL) mode. For returning TC SOURCE to the previous EXT mode. (No switching occurs if the EXT mode is currently established. ) For switching TC SOURCE to INT and TCG MODE to AUTO. Pin status "1" signifies "active low" and "0" signifies "open. " Error statuses C22 ERR0 0 0 0 0 C23 ERR1 0 0 1 1 C24 ERR2 0 1 0 1 Error status SERVO NOT LOCKED (priority level 1) SERVO LOCKED (priority level 4) HIGH ERROR (amber) (priority level 3) HIGH ERROR (red) (priority level 2) 50P IN/OUT ASSIGN Up-conversion statuses C17 UC1 0 0 1 C18 UC2 0 1 0 Up-conversion status Stretch mode Side panel mode Top and bottom cut in vertical direction Up-conversion down-conversion statuses C19 UD1 0 0 1 C20 UD2 0 1 0 1 C21 UD3 0 0 0 1 Down-conversion status Squeeze mode Side cut mode Letter box mode Up-conversion status Stretch mode Side panel mode Top and bottom cut in vertical direction TC input statuses C12 TC SRC1 0 0 1 1 C13 TC SRC2 0 1 0 1 TC input status 1 External SLTC External LTC External SVITC (or external VITC with SD input) INT Any other combination Tape recording inhibit statuses C10 CAS INH1 0 0 C11 CAS INH2 0 1 Tape recording inhibit status Cassette recording enabled Cassette accidental erasure prevented Recording inhibit statuses C08 REC INH1 0 0 1 1 C09 REC INH2 0 1 0 1 Recording inhibit statuses Overwriting prohibited during normal recording All recording onto cassette prohibited Recording inhibit mode other than the 2 above modes Recording onto cassette enabled Down-conversion statuses C14 DC1 0 0 1 1 1 C15 DC2 0 1 0 1 1 C16 DC3 0 0 0 0 1 Down-conversion status Squeeze mode Side cut modea Letter box mode 14:9 13:9 75 Function menus <50P IN/OUT ASSIGN> Flow of registration Press the ADJ dial. Status in which selected 50pin connector pin menu item selection is enabled Turn the ADJ dial. F1 (forward page scroll) F2 (reverse page scroll) Open the screen. F6 (EXIT) Status in which registered 50-pin connector pin selection is enabled Turn the ADJ dial. F4 (one pin reset) F i F4 (all pins reset) F5 (settings entered) F3 (cancel) Press the ADJ dial. Status in which selected menu item setting selection is enabled Press the ADJ dial. F3 (cancel) Turn the ADJ dial. 50P IN/OUT ASSIGN function buttons Function button/item F1 : PREV F2 ; NEXT F3 CANCEL F4 RESET Switching method Press Press Press Setting ___ ___ ___ Corresponding setup menu item ___ ___ ___ Description of setting For scrolling the on-screen menu pages in the forward direction. For scrolling the on-screen menu pages in the reverse direction. For releasing the menu item selection status. For resetting one pin: what has been selected for the pin selected by the individual reset selection marker is cleared. For resetting all the pins: what has been registered in all the pins is set to the factory settings and set in the 50-pin registration file. For registering the file; all the function button settings are saved in the 50-pin registration file. [. . . ] BNC k 1 (board, option) 1 2 3 FRAME GROUND TRANSMIT A RECEIVE B RECEIVE COMMON ==== TRANSMIT COMMON TRANSMIT B RECEIVE A FRAME GROUND Signal AUDIO IN AUDIO IN (DIGITAL) AUDIO IN (ANALOG) HD SERIAL IN (DIGITAL) SD SERIAL IN (DIGITAL) CUE IN TIME CODE IN BNC k 4 (CH1/CH2, CH3/CH4, CH5/CH6, CH7/CH8), AES/EBU format XLR k 4 (CH1, CH2, CH3, CH4) BNC k 1, active-through (BNC k 1) BNC k 1, active-through (BNC k 1) (board, option) XLR k 1 XLR k 1 4 5 6 7 8 9 O REMOTE OUT Pin No. 1 2 3 4 5 6 7 8 9 FRAME GROUND RECEIVE A TRANSMIT B TRANSMIT COMMON ==== RECEIVE COMMON RECEIVE B TRANSMIT A FRAME GROUND Signal 128 Connector signals PARALLEL REMOTE (50P) Refer to 50P IN/OUT ASSIGN on the function menu (page 75) for the connection pin signals. ENCODER REMOTE(15P) Pin No. 1 FRAME GROUND REM (G) REM RX (X) REMOTE CONTROL PROTOCOL RECEIVE REM TX (X) REMOTE CONTROL PROTOCOL TRANSMIT REM RX (Y) REMOTE CONTROL PROTOCOL RECEIVE REM TX (Y) REMOTE CONTROL PROTOCOL TRANSMIT Signal RS-232C (D-SUB 25-pin, crossover cable supported) Pin No. 1 2 3 4 5 6 7 20 Signal FG RXD TXD CTS RTS DTR SG DSR Description Protective ground (frame ground) Received data (data is sent to PC) 4 7 8 14 15 Transmitted data (data is received from PC) Clear to send (shorted with pin 5) Request to send (shorted with pin 4) Data terminal ready (no processing) Signal ground Data set ready (+ voltage output after communication enable status) Printed circuit boards F1 board (ADDA) Switch No. [. . . ]