User manual PANASONIC AJ-HDP2000

[. . . ] Operating Instructions 2K Processor Model No. AJ-HDP2000P Before operating this product, please read the instructions carefully and save this manual for future use. F0707N0 -F @ Printed in Japan ENGLISH VQT1F04 Read this first! _ DO NOT REMOVE PANEL COVERS BY UNSCREWING THEM. To reduce the risk of electric shock, do not remove the covers. Refer servicing to qualified service personnel. FCC Note: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] When the ON side is pressed, the power is turned on; when the OFF side is pressed, the power is turned off. | : Press the " | " side of the power switch to turn the power on. ±: Press the " ± " side of the power switch to turn the power off. This lights when a problem has occurred in the main unit, making it impossible to guarantee operation. (Refer to the messages on page 13. ) This displays the H sample of the video signal that is system setting. !3" Alarm Lamp !4" Horizontal Sample Display Lamp 6 Controls and their Functions (Continued) 2. Connector Section (Rear) !4" !5" !6" !7" !8" !9" !13" !12" !10" !11" !2" !1" !3" !1" AC Input Socket !2" Fuse !3" GND (ground) Terminal !4" Dual-Link SDI Input !5" Dual-Link SDI Output 1, 2 Use the accessory power cord to connect the socket to the power outlet Power circuit fuse When connected with another unit, the unit must be ground here For inputting the Dual-Link digital signals For outputting the Dual-Link or HD digital signals (4:4:4/4:2:2 switchable) For outputting the HD digital signals (4:2:2 samples) This is connected to the HD SDI OUT connector on the HD-D5 VTR for inputting for video/ audio/ tc output data from the HD-D5 VTR. This is connected to the HD SDI IN connector on the HD-D5 VTR for outputting the video/ audio/ tc data. This is connected to the REF IN HD connector on the HD-D5 VTR. The sync signal re-generated from the HD REF IN signal of the processor. The VANC/HANC data, such as Audio/TC/Meta/Payload information, is not embedded on the OUTPUT MON (Monitor) output. In OUTPUT MON (Monitor) and when the 4:2:2 format is selected for the main system, an H CROP function for 1920 samples is available in 2048 samples. However, the Squeeze and Letter Box functions are not available. The following three kinds of modes are available as fixed Crop modes. CTR Crop: Both sides are equally cropped so that the number of samples is 1920. L Crop: The left side is cropped so that the number of samples is 1920. R Crop: The right side is cropped so that the number of samples is 1920. OUTPUT MON (Monitor) has a function to turn on/off superimposition in SUPER. 8 Controls and their Functions (Continued) 3. 3. AUDIO Input Audio Input Signal Dual Link SDI Input (Embedded Audio) BNC a 2, 75 SMPTE 299M standard For AUDIO input, an SDI Embedded Audio function is available with the 2K processor, and AES/EBU Digital Audio, Analog Audio, and CUE Audio inputs are available from the HD-D5 VTR in a manner similar to the single operation of the HD-D5 VTR. The AUDIO input signal is selected in FRONT MENU of the main unit in a manner similar to the single operation of the HD-D5 VTR. SDI Embedded Audio input signals are available only for Ach of Dual Link SDI signals. 3. 4. AUDIO Output Audio Output Signal Dual Link SDI Output (Embedded Audio) BNC a 2 a 2, 75 SMPTE 299M standard For AUDIO output, an SDI Embedded Audio function is available with the 2K processor, and AES/EBU Digital Audio, Analog Audio, and CUE Audio outputs are available from the HD-D5 VTR in a manner similar to the single operation of the HD-D5 VTR. The AUDIO output signal is selected in FRONT MENU of the HD-D5 VTR in a manner similar to the single operation of the HD-D5 VTR. [. . . ] (Tape ID = 1920) Example 2: Input of 1920 signals with 2048 selected in SYSTEM settings: Black signals of 64 samples are added to each side to record as 2048 samples. (Tape ID = 2048) 2048 1920 2048 1920 64 1920 64 2048 2048 1920 64 1920 64 1920 1920 1920 1920 15 Restrictions (Continued) Differences in the actual image conditions due to differences in the number of H Samples between SYSTEM settings and Tape playback (Tape recording ID) (According to the SYSTEM settings) SYSTEM settings (MENU selection) TAPE playback signals 2048 CTR CROP 2048 1920 2048 1920 1920 H CROP (MENU selection) SAMPLING = 4:4:4 output images SAMPLING = 4:2:2 output images 1920 2048 L CROP 1920 R CROP 1920 CTR CROP 2048 1920 64 1920 64 1920 1920 L CROP 1920 R CROP 1920 2048 2048 1920 64 1920 64 1920 1920 1920 Internal signal source (INT-SG) There are four internal signal sources: CB1, CB2, BLACK, and WHITE. (10-bit precision) XYZ and RGB color spaces are expressed differently, resulting in a difference in the internal signal format. <In SYSTEM Color Space = RGB> CB1: 100% Color Bar CB2: 75% Color Bar <In SYSTEM Color Space = XYZ> CB1: Color Bar Signal Pattern 1 CB2: Color Bar Signal Pattern 2 INPUT CHECK Function Pressing the INPUT CHECK button changes the TC display in the monitor output SUPER and the TCG display in the front panel to the internal TCG. [. . . ]