User manual PANASONIC AJ-HDX900P

[. . . ] Operating Instructions Camera-Recorder Model No. AJ- P E Before operating this product, please read the instructions carefully and save this manual for future use. F0706W0 -F @ Printed in Japan ENGLISH VQT0X86 Read this first!(For AJ-HDX900P) CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. WARNING: OTO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. [. . . ] The VISTA setting is 16:8. 65. FRM SIG 4:3 13:9 14:9 VISTA ON OFF VIDEO OUT USER BOX For superimposing the user box on the output signals from the VIDEO OUT connector. ON: To superimpose OFF: Not to superimpose O It is not superimposed when the VIDEO OUT switch is set to the SD-SDI or the VBS position. For setting the horizontal width of the user box. USER BOX WIDTH 1 : 13 : 100 USER BOX HEIGHT 1 : 13 : For setting the vertical height of the user box. 100 USER BOX H POS ­50 : +00 : For setting the horizontal position of the user box center. +50 USER BOX V POS ­50 : +00 : For setting the vertical position of the user box center. +50 O The user box can be displayed in any position as a boxtype cursor. 59 Chapter 4 Adjustments and settings for recording (continued) 4-8-2 Settings of signals output from MON OUT connector Set the video signals output from the MON OUT connector by using the MONI OUT item on the menu (<OUTPUT SEL> screen on the SYSTEM SETTING page). The HD-Y signals can be used for applying GEN LOCK to other devices. It is impossible to superimpose markers and characters on the HD-Y signals. Even when the tape is replayed, images from the camera are output. Item MONI OUT Variable range HD-SDI HD-Y Remarks Set video signals output from the MON OUT connector. HD-SDI: For outputting the HD SDI signals HD-Y: For outputting the analog HD-Y signals MONI OUT SAFETY MARK OFF 1 2 Set the marker and user boxes to superimpose on the output signals from the MON OUT connector by using the respective items on the <MONITOR OUT SETTING> screen (SYSTEM SETTING page) of the menu. Item MONI OUT CENTR MARK Variable range OFF 1 2 3 4 Remarks For setting the center marker to be superimposed on the HD SDI output signals of the MON OUT connector. OFF: The center marker is not displayed. 1: + (large) 2: Center blank (large) 3: + (small) 4: Center blank (small) For setting the type of the safety marker frame to be superimposed on the HD SDI output signals of the MON OUT connector. OFF: The safety marker frame is not displayed. 1: Box Set to superimpose characters to the HD SDI signals output from the MON OUT connector in the MONI OUT CHARA item of the menu (<OUTPUT SEL> screen on the SYSTEM SETTING page). Item MONI OUT CHARA Variable range ON OFF Remarks Superimpose characters on the HD SDI output signals from the MON OUT connector. ON: To superimpose OFF: Not to superimpose <Note> This does not link with the VIDEO OUT CHARACTER switch. SAFETY AREA 80% : 2: Corner frames 90% : 100% MONI OUT FRM MARK ON OFF For setting the size of the safety marker. It is possible to set the size by units of 1% with a fixed ratio between of width and height. For superimposing the frame marker on the HD SDI output signals from the MON OUT connector. ON: To superimpose OFF: Not to superimpose For setting the frame marker. The VISTA setting is 16:8. 65. FRM SIG Switch the signals output from the MON OUT connector by using MONI OUT MODE item on the menu (<OUTPUT SEL> screen on the SYSTEM SETTING page). Item MONI OUT MODE Variable range CAM VTR MONI OUT USER BOX Remarks Switch the signals output from the MON OUT connector. CAM: The camera images are output at all times. VTR: In the recording or other EE mode, camera images are output from the connector; in playback mode, the VTR's playback signals are output. 4:3 13:9 14:9 VISTA ON OFF For superimposing the user box on the HD SDI output signals from the MON OUT connector. ON: To superimpose OFF: Not to superimpose For setting the horizontal width of the user box. USER BOX WIDTH 1 : 13 : 100 USER BOX HEIGHT 1 : 13 : For setting the vertical height of the user box. 100 USER BOX H POS ­50 : +00 : For setting the horizontal position of the user box center. +50 USER BOX V POS ­50 : +00 : For setting the vertical position of the user box center. +50 O The user box can be displayed in any position as a boxtype cursor. 60 Chapter 4 Adjustments and settings for recording (continued) 4-9 Menu-driven function setup The functions can be set up using the unit's menus. 4-9-2 Selecting the F. AUDIO LEVEL control function This function enables the recording level to be adjusted using the F. AUDIO LEVEL control. To select this function, perform menu operations to open the <MIC/AUDIO> screen from the VTR MENU page, and set whether to enable or disable the F. AUDIO LEVEL controls for the system selected as the input signals using the FRONT VR CH1 and FRONT VR CH2 items. #< MIC/AUDIO1 > FRONT VR CH1 FRONT VR CH2 MIC LOWCUT CH1 MIC LOWCUT CH2 MIC LOWCUT CH3 MIC LOWCUT CH4 LIMITER CH1 LIMITER CH2 AUTO LEVEL CH3 AUTO LEVEL CH4 REC CH3/CH4 CUE REC SELECT TEST TONE :OFF :OFF :OFF :OFF :OFF :OFF :OFF :OFF :ON :ON :SW :CH1 :NORMAL 4-9-1 Setting the USER SW GAIN switching This unit allows three other modes to be used in addition to the L/M/H standard gain settings: the analog gain-up S. GAIN (super gain) mode to achieve a gain of 30 dB or more, the cumulative gain-up DS. GAIN (digital super gain) mode which uses progressive drive, and the LINE MIX GAIN mode where the gain of two lines is mixed. To select these functions, perform menu operations to open the <USER SW GAIN> screen from the OPERATION page, select the S. GAIN item and DS. GAIN item, and preset the gain to be used for each item. [. . . ] For displaying the version of the FPGA for video signal processing. For displaying the version of the PLD for controlling the SD memory card. 1394 CONFIG DFLT 1 : DRUM RUNNING r C 1394 GAP COUNT 255 0 : THREADING r 40 : VTR SYSCON C 63 SERVO LCD VIDEO FPGA PWR PLD The underlining in the variable range column indicates the setting in the preset mode. 131 Chapter 8 Specifications [GENERAL] Power supply: DC 12 V (DC 11. 0 V - 17. 0 V) Power consumption: 36 W indicates safety information. Ambient operating temperature: 0°C to +40°C (32°F to 104°F) Storage temperature: ­20°C to +60°C (­4°F to 140°F) Ambient operating humidity: Within 10% to 85% (relative humidity) Continuous operation time: Approx. [. . . ]