User manual PANASONIC AJ-LT75

[. . . ] OTO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS. USE AND STORE ONLY IN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DRIPPING OR SPLASHING LIQUIDS, AND DO NOT PLACE ANY LIQUID CONTAINERS ON TOP OF THE EQUIPMENT. FCC Note: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] However, the switching operation is not acknowledged during the recording operation. VTR: In the recording or other EE mode, camera images are output from the connector; in playback mode, the VTR's playback signals are output. CAM: The camera images are output at all times. VIDEO OUT OUTPUT SEL switch Set the characters to be superimposed on the signals output from the VIDEO OUT connector by using the VIDEO OUT CHARACTER switch and the OUTPUT ITEM item on the menu (<OUTPUT SEL> screen on the SYSTEM SETTING page). VIDEO OUT CHARACTER switch 58 Chapter 4 Adjustments and settings for recording (continued) Set the marker and user boxes to superimpose on the output signals from the VIDEO OUT connector by using the respective items on the <VIDEO OUT SETTING> screen (SYSTEM SETTING page) of the menu. Item VIDEO OUT CENTR MARK Variable range OFF 1 2 3 4 Remarks For setting the center marker to be superimposed on the output signals of the VIDEO OUT connector. OFF: The center marker is not displayed. 1: + (large) 2: Center blank (large) 3: + (small) 4: Center blank (small) For setting the type of safety marker frame to be superimposed on the output signals of the VIDEO OUT connector. OFF: The safety marker frame is not displayed. 1: Box VIDEO OUT SAFETY MARK OFF 1 2 <Notes> O When the DOWNCON MODE item on the DOWNCON SETTING screen is set to LT-BOX or S-CROP, the frame marker and the safety marker are not displayed. O Settings in the SAFETY AERA item and the FRM SIG item are interlinked with the respective connectors of VIDEO OUT, MON OUT, and REMOTE. O Settings for the respective items of USER BOX WIDTH, USER BOX HEIGHT, USER BOX H POS, and USER BOX V POS are interlinked with the VIDEO OUT connector and the MON OUT connector. 4 2: Corner frames SAFETY AREA 80% : 90% : 100% VIDEO OUT FRM MARK ON OFF For setting the size of the safety marker. It is possible to set the size by units of 1% with a fixed ratio between of width and height. For superimposing the frame marker on the output signals from the VIDEO OUT connector. To select these functions, perform menu operations to open the <USER SW GAIN> screen from the OPERATION page, select the S. GAIN item and DS. GAIN item, and preset the gain to be used for each item. Furthermore, select the LINE MIX function on the <USER SW> screen. For instance, if the S. GAIN, DS. GAIN and LINE MIX GAIN functions have been allocated to the USER MAIN button, USER1 button or USER2 button, the gain can be increased by using these buttons in combination with the USER buttons. 1) To increase the gain without increasing the perceptible noise The DS. GAIN function and the LINE MIX GAIN function are used. 2) To increase the normal analog gain (in which case, the amount of noise will increase) Use only the S. GAIN function. <Note> Note that the accuracy of AUTO IRIS, White Balance, and Black Balance may be influenced by an increase in noise. 3) To use the unit in the ultra-high-sensitivity mode Use the S. GAIN function and DS. GAIN or LINE MIX GAIN function in combination. However, exercise care during operation since image lag will become more conspicuous with moving subjects the more the gain is increased by using the DS. GAIN function. When shooting moving subjects, keep the gain increase with the LINE MIX GAIN function or DS. GAIN function to under +12 dB. #< USER SW GAIN > S. GAIN ¢30dB ¢36dB 4 Setting items and what is set Item FRONT VR CH1 Variable range FRONT W. L. REAR ALL OFF Remarks For selecting whether or not to enable the F. AUDIO LEVEL control for the input signals which have been selected for audio CH1. FRONT: The control works only when FRONT has been selected. [. . . ] For displaying the total number of times cassettes have been loaded after resetting. For displaying the software version of the VTR SYSCON microcomputer. For displaying the software version of the SERVO microcomputer. For displaying the software version of the LCD microcomputer. [. . . ]