User manual PANASONIC AJ-RC10G

[. . . ] / Remote Control Unit/Fernsteuereinheit/ Module de télécommande/ Unità per il comando a distanza/Unidad de control remote/ Before operating this product, please read the instructions carefully and save this manual for future use. Bitte lesen Sie vor Inbetriebnahme dieses Produkts die Anleitungen sorgfältig durch und bewahren Sie dieses Handbuch für spätere Verwendung auf. Avant de vous servir de ce produit, veuillez lire attentivement les instructions et enregistrer ce manuel pour une utilisation ultérieure. Prima di utilizzare questo prodotto, leggere attentamente le istruzioni di questo manuale e conservarlo per riferimento futuro. [. . . ] However, do not leave the unit without these screws for long periods of time. When the screws are not in use, they must be stored safely. <Note> Do not remove the four screws on the back panel. LEVEL VIDEO OUT CAM RCU CABLE 50m 10m FREQUENCY !3" !4" !5" !1" Camera connection connector To connect the 10-pin camera control cable. Pin No. 18 2 9 10 3 45 6 7 Signal CAM DATA (H) CAM DATA (C) CAM CONT (H) CAM CONT (L) ECU_ON Video input GND (Video) Standby +12 V (IN) GND 1 2 3 4 5 6 7 8 9 10 !2" VIDEO OUT connector An NTSC or PAL monitor is connected for operating the menu on the main unit of the camera recorder. !3" Cable length selector switch This switch is on for a 50 m cable. !4" Frequency characteristics adjustment volume This adjusts the frequency characteristics of the VIDEO signals. !5" Level adjustment volume This adjusts the level of the VIDEO signals. E-15 When the power is on When the POWER button is pressed, the lamp for the PANEL ACTIVE button is on, and the settings of the camera recorder are read into the unit. The respective numerical values are displayed on the PRE/A/B display, CC/ND display, GAIN display, and the IRIS display, while R GAIN and B GAIN are displayed on the LCD panel. In this case, only the PANEL ACTIVE button, the SW ACTIVE button, the VR ACTIVE button, the AUTO IRIS button, M. PED volume and the IRIS volume can be operated from the unit, while other buttons and volumes are not operative. However, the settings on the A. KNEE ON button, the SHT ON button , the AUTO IRIS button, the BAR ON/OFF button and the CHARA ON button will be in the states that had been set on the unit at the last time. 3) To display numerical values on the LCD panel The GAIN volume is displayed when the power is on. If the button operations are enabled, it is possible to switch the displayed GAIN volume # BLACK volume # a numerical value for M/ PED # TC step-by-step by using the 3button and the 4button. When volume operation is enabled, the volume level is forcibly displayed if the GAIN volume or the BLACK volume is operated. However, it is possible to return the screen to the state before operating the GAIN volume or the BLACK volume by pressing the Rotary Encoder 3. <Note> It is impossible to switch the display when the unit menu or the camera menu is operating. The volume level is not displayed even if the volume is operated. To enable the buttons/volumes When the SW ACTIVE button is pressed and the lamp is on, button operations are enabled. To disable buttons/volumes If the lamp of the PANEL ACTIVE button is turned off, operations using the buttons and the volume on the panel are inhibited. If the lamp of the VR ACTIVE button is turned off by pressing the button, setting the GAIN and BLACK using the volume controls is inhibited. Use this feature if you intend to retain the settings. However, note that if the volume is moved when inhibited, the volume level change will be reflected immediately after turning on the lamp of the PANEL ACTIVE button and/or the VR ACTICE button by pressing the button again. 1) Operations of the camera part When the SW ACTIVE button is pressed, operations of the USER MAIN button, GAIN and the camera recorder such as storing scene files in the built-in memory or reading them out, are enabled. When the SW ACTIVE button is pressed again, the lamp is tuned off and button operations are inhibited, while the state of settings that have already been set previously is remained as it is. <Note> It is possible for the GAIN and the BLACK to avoid changes in the volume position during the inhibition by setting the volume mode on the unit menu to a relative value (REL). 2) Operation of the recording part When the lamp of the RECORDER ENABLE button is turned off, operations of the recording part are disabled. Turn on the lamp of the RECORDER ENABLE button by pressing the button, and then operate the buttons of "PLAY", "FF" or "REW". To record signals, operate the REC S/S button. E-16 ENGLISH Basic operations Basic operations (Continued) Operation of the camera recorder 1) Operation of the display interlocking switch Select the white balance settings by using the PRE/A/B button and monitoring the PRE/A/B display. The state of the camera recorder filter is displayed on the CC/ND display. If two filters are installed on the camera recorder, it is impossible to switch the filters from the unit but it is possible to switch the display by using the FILTER ND/CC button. The ND filter is indicated with numerical values while the CC filter is indicated with letters of the alphabet. The gain will change when using the two buttons of the M. GAIN3 button and M. GAIN4 button and monitoring the GAIN display. However, if super gain is set to ON in the USER switch, operations of the MGAIN button are disabled. 4) Operation of other switches For the MATRIX ON button, the DTL OFF button, A. KNEE ON button, HIGH COLOR ON button, and the SHT ON button, the ON and OFF states switch every time the button is pressed. [. . . ] To adjust the color phase of the color correction axis selected in the C-COR. SATU PHASE <Note> For the adjustment of the shading, the adjusted setting on the unit will be retained in the main unit of the camera recorder regardless of the ON/OFF setting on the RCDATA-SAVE item. E-28 ENGLISH Menu item (Continued) Menu item (Continued) DTL Layer 1 Item MDTL Variable Contents description Storage range ­31 : +31 0 : 63 0 : 31 OFF 0 : 5 0 : 31 0 : 5 OFF 0 : 5 ­31 : +31 ­31 : +31 0 : 63 To set the level of the master detail (H and V) To set the H. DTL LEVEL To set the V. DTL LEVEL SKIN DTL Layer 1 Item S DTL Variable Contents description Storage range OFF A B AB To select the skin tone table that enables skin tone details OFF: To select OFF of the skin color DTL A: To put DTL in the SKINTONE setting set in Table A B: To put DTL in the SKINTONE setting set in Table B AB: To put DTL in the Yes SKINTONE setting set in Tables A and B To select the output that adds SKINZEBRA To select ON/OFF for SKIN ZEBRA against the output selected in OUTPUT The ZEBRA will be attached to the color of the table set in DETECT. To select the table for setting SKIN TONE to be adjusted using the unit To set the effects of SKIN TONE DTL scoring To set the maximum value of the brightness signals enabling SKIN TONE To set the minimum value of the brightness signals enabling SKIN TONE Yes HDTL Yes VDTL 2 CORG To set detailed noise elimination level FREQ To set the H. DTL FREQ Yes LDP To set the LEVEL DEPEND To set the details of the high brightness part OUTPUT SZEB MONI VIDEO ON OFF 3 K-AP +GAIN To change the level in the + direction of the H. DTL To change the level in the ­ (down) direction of the H. DTL To change the clip in the + direction of the DTL signals Yes ­GAIN 2 TABL A B 4 CLIP 3 SCORG SOURCE R+G To set the signal source Yes G+B of the DTL signal 2G+R+B components 3G+R R G 0 : 7 0 : 255 0 : 255 Yes 4 YMAX YMIN Yes E-29 SKIN DTL (Continued) Layer 5 Item ICENT Variable Contents description Storage range 0 : 255 0 : 255 To set the center position on the I-axis (to set the area where SKIN TONE is effective) Yes To set the width of the area where SKIN TONE on the I-axis with the center position at I CENT is effective To set the width of the area where SKIN TONE on the Q-axis with the center position at I CENT is effective Yes To set the phase of the area where SKIN TONE having a standard on the Q-axis is effective This will be used for obtaining the color phase as the target for SKIN TONE DTL No FUNC Layer 1 Item IRISLVL Variable Contents description Storage range 0 : 100 To set the target value of the auto iris Yes To determine the accounting ratio of the peak against the standard of the auto iris IWIDTH PEAK/AVE 0 : 100 2 IRISWINDOW 6 QWIDTH 0 : 255 QPHASE ­128 : +127 EXEC NORM1 To select the auto iris NORM2 detection window CENTER NORM1: Center of the screen NORM2: Bottom side of the screen CENTR: Spots at the center of the screen CAM LENS To select whether the iris gain is adjusted on the camera recorder or the lens To set the IRIS GAIN adjustment value on the camera recorder To select the USER switch where functions will be changed Yes 3 IRISGAIN 7 SKIN-GET Yes GAINVAL 1 : 20 USW-M USW-1 USW-2 4 USER-SW SELECT INH To select the function to S/GAIN be assigned to the DS. GAIN USER button selected LINE MIX in the USER-SW item S. IRIS <Note> I. OVR When the unit is Yes S. BLK connected to the B. GAMMA camera recorder, the AUDIO CH1 "I. OVR" operation is AUDIO CH2 disabled. REC SW Y GET RET SW PRE REC DRS E-30 ENGLISH Menu item (Continued) Menu item (Continued) FUNC (Continued) Layer 5 Item BLKGAMMA Variable Contents description Storage range ­3 ­2 ­1 OFF 1 2 3 ON OFF To set the gamma curve for dark portions Yes SYSTEM Layer 1 Item CARDREAD TITLE Variable Contents description Storage range 1 : 8 To select the file number to be read out No ¢¢¢¢¢ To read out the title ¢¢¢ applied to the data of the file to be read out, and display it 1 : 8 To select the file number to be written 6 RC-DATASAVE To select whether the value adjusted in the unit will be retained in the main unit of the camera recorder or not, when the unit is removed from the camera recorder Yes When this is set to OFF and the unit is removed, the settings for the camera recorder will return to the state before connecting the unit. 2 CARDWRITE TITLE ¢¢¢¢¢ To enter the title applied ¢¢¢ to the data of the file to be written 1 : 8 To select the file number to be deleted No 3 CARDDELETE TITLE ¢¢¢¢¢ To read the title applied ¢¢¢ to the data of the file to be deleted, and display it To configure the card ON OFF To select whether the buzzer is turned on when the switch for the lamp to turn on is pressed To adjust the contrast of the LCD panel No 4 5 CARDCONFIG BUZZER No No 6 LCD 0 CONTRAST : 10 : 15 SW BRIGHT 0 : 10 : 15 RCUFACTRY No 7 To adjust the brightness of the lamp for the switch No 8 To return the volume variable range of the unit to the factory settings To display the version of the software for the unit No 9 VERSION No is the factory setting E-31 A 10 m connection cable is attached to the unit. To extend the cable, use the optional dedicated cable. [. . . ]