User manual PANASONIC AJ-SD955B

[. . . ] Digital Video Cassette Recorder Operating Instructions AJModel No. P P AJ- Before operating this product, please read the instructions carefully and save this manual for future use. P Printed in Japan S0903W @ VQT0F41 IMPORTANT "Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws. " CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER MOUNTING OF THE OPTIONAL INTERFACE BOARD TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER CHANGE OF SWITCH SETTING INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL. CAUTION: OKeep the temperature inside the rack to between 41°F to 104°F (5°C to 40°C). OBolt the rack securely to the floor so that it will not topple over when VTR is drawn out. [. . . ] 0000 0001 OFF : Connector does not function. ON : Connector functions. 212 SD955B MASTER PORT 205 BAUD RATE These settings are for selecting the RS-232C communication speed (baud rate). 0000 0001 0002 0003 0004 0005 300 600 1200 2400 4800 9600 For selecting the remote control connector to control the slave when the unit is used as the master during deck-to-deck operations. 0000 IN/OUT : The IN/OUT connector is used. <Note> This menu item takes effect only when the CONTROL switch has been set to the LOCAL position. 206 DATA LENGTH 207 STOP BIT These settings are for selecting the RS-232C data length. (Unit: bit) 0000 0001 7 8 These settings are for selecting the RS-232C stop bit length. (Unit: bit) 0000 0001 1 2 The underlined items indicates the initial setting. 39 Setup menus USER menu No. /Item 301 SD955B IN/OUT DEL <EDIT> Description No. /Item 306 EDIT RPLCE2 Description The same type of setting as setup menu No. This selects the channel concerned when the CH2 edit preset is set in compliance with the ON or OFF presetting for the analog audio signals designated by the controller. 0001 CH1 : Compliance with analog CH1 edit preset. 0002 CH2 : Compliance with analog CH2 edit preset. 0003 CH1+2 : Compliance with either analog CH1 or CH2 edit preset. 307 EDIT RPLCE3 The same type of setting as setup menu No. This selects the channel concerned when the CH3 edit preset is set in compliance with the ON or OFF presetting for the analog audio signals designated by the controller. 0001 CH1 : Compliance with analog CH1 edit preset. 0002 CH2 : Compliance with analog CH2 edit preset. 0003 CH1+2 : Compliance with either analog CH1 or CH2 edit preset. 308 EDIT RPLCE4 The same type of setting as setup menu No. This selects the channel concerned when the CH4 edit preset is set in compliance with the ON or OFF presetting for the analog audio signals designated by the controller. 0001 CH1 : Compliance with analog CH1 edit preset. 0002 CH2 : Compliance with analog CH2 edit preset. 0003 CH1+2 : Compliance with analog CH1 or CH2 edit preset. This selects the operation to be performed when an edit point has been set incorrectly (when the OUT point is before the IN point). 0000 MANU : Editing is not executed unless the illegal edit point is cleared or set again properly. [. . . ] O Editing operations can be performed only when all the video and audio signals as well as the time codes in the SDTI input signals are regular data based on the DVCPRO50 or DVCPRO format selected by setup menu No. O CUE signals are not transferred by the SDTI interface. O SDTI dubbing is not possible from tapes recorded using the DV or DVCAM format. Use SDI when dubbing tapes recorded in the DV or DVCAM format. [. . . ]