User manual PANASONIC AJ-SDC915

[. . . ] Digital Camera/VTR Operating Instructions Model No. AJ- P Before operating this product, please read the instructions carefully and save this manual for future use. P Printed in Japan F0802H D VQT0A45 For your safety CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN FCC NOTE: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] However, if the reference time code is disconnected during recording (REC), the servo lock will be thrown out of order. |Note{ When the external locking operation is performed, the time code is locked instantly to the external time code and the same value as the external code value appears in the counter display position. Do not set the VTR to recording mode for several seconds until the sync generator has stabilized. Setting Time Data User bit setting during external locking When the time code is locked to an external source, only the time data is locked to the time data of the time code from the external source. Accordingly, the user bit can be set independently for each unit. The user bit can also be locked to the user bit of the time code from the external source. Consult your dealer for a detailed explanation. Releasing the external lock Stop supplying the external time code and then set the F-RUN/R-RUN switch to R-RUN. Switching the power supply from the battery to an external power supply during external locking In order to maintain power supply continuity for the time code generator, connect the external power supply to the DC IN connector before unplugging the battery pack. If the battery pack is unplugged first, the external locking continuity of the time code cannot be assured. Synchronizing the camera section to an outside source during external locking During external locking, the camera section is genlocked by the reference video signal which is supplied to the GENLOCK IN/(VIDEO IN) connector. Using the user data The setting menu contents can be saved in the user area of the camera's memory so that they can be loaded as and when required. This data enables the suitable setup statuses to be re-established without delay. User data operation A menu is used to save the data settings in the user area of the camera's memory or to load them. Saving the user data 1 The menu's INITIALIZE screen is used to save the user data. 2 Set the MENU SET/OFF switch to the SET position while the SHIFT/ITEM button and UP button are held down together. 3 Press the PAGE button to display the MAIN menu screen 4 of 4. 4 Press the SHIFT/ITEM button to move the cursor to the "INITIALIZE" position. 5 Press the UP or DOWN button to open the INITIALIZE page. When the SHIFT/ITEM is pressed to align the arrow with WRITE USER DATA and the UP or DOWN button is pressed, the data settings will be saved in the user area of the camera's memory. 6 After the settings have been saved, set the MENU SET/OFF switch to the OFF position. Loading the user data 1 The menu's CARD READ/WRITE screen is used to set the unit to the status in which the data settings were saved in the user area of the camera's memory. 2 Set the MENU SET/OFF switch to the SET position while the SHIFT/ITEM button and UP button are held down together. 3 Press the PAGE button to display the MAIN menu screen 3 of 4. 4 Press the SHIFT/ITEM button to move the cursor to the "CARD READ/WRITE" position. [. . . ] Turn the AUDIO LEVEL CH1/CH2 controls and check that the level display increases when the controls are turned to the right. (4) Earphone and Speaker Inspections 1 2 3 4 1 2 3 Set the VTR SAVE/STBY switch to STBY. Turn the MONITOR control and check that the speaker volume changes. Check that the sound to the speaker is cut off and that the microphone sound can be heard from the earphone. Turn the MONITOR control and check that the earphone volume changes. (5) Inspections when Using an External Microphone Connect an external microphone to the AUDIO IN CH1 and CH2 connectors. [. . . ]