User manual PANASONIC AJ-SPC700P

[. . . ] Operating Instructions Memory Card Camera Recorder Model No. AJ- P Before operating this product, please read the insructions carefully and save this manual for future use. F0705T2056 -F D Printed in Japan ENGLISH VQT0T98-2 Read this first! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. FCC Note: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] This operation does not delete the scene file, lens file, and the information stored as the user data. 4-10-6 Lens File Data The AJ-SPC700P is capable of correcting the lens white shading. This lens white shading correction may be stored as lens file data (maximum number of data sets is eight). Lens file data allows you to quickly perform a proper white shading adjustment, even when the lens is replaced. For more information on reading/writing data, see [5-3 Mounting the lens and Performing the Flange Back and White Shading Adjustments]. 63 Chapter 5 Preparation 5-1 Power Supply A battery pack or an external DC power supply can be used as this unit's power supply. 2 Insert the battery and slide it in the direction of the arrow. Using a Battery Pack Battery packs from the following manufacturers can be used: · Anton/Bauer · IDX · PACO · Sony <Notes> Other batteries may be used by changing the menu setting, but system compatibility is not guaranteed. Charge the battery pack with the battery charger before using it. (Please refer to the battery charger's instruction manual for information about charging. ) Release lever <For your information> Removing the battery pack Completely push down and hold the release lever on the battery holder. Then, slide the battery pack in the opposite direction to the arrow while holding the lever down. 3 Setting the battery type. Select the battery type listed under BATTERY SELECT. Select BATTERY SELECT from the <BATTERY/ P2CARD> screen in the MAIN OPERATION page. Please refer to [8-6-2 BATTERY SETTING1] for more information. 5-1-1 Mounting the Battery and Setting the Battery Type Using an Anton/Bauer Battery Pack 1 Mount the Anton/Bauer battery pack. Power supply output connector for lighting The following Anton/Bauer batteries can be used: · PRO14 · TRIM14 · HYTRON50 · HYTRON100 · HYTRON120 · DIONIC90 · DIONIC160 <Note> To use DIONIC, please set it as DIONIC90. Anton/Bauer Battery Pack Lighting control switch <For your information> The Anton/Bauer battery holder includes both a power supply output connector for lighting and a lighting control switch, which are convenient when attaching a light. Please contact Anton/Bauer for information about the lighting system. 64 Chapter 5 Preparation (continued) When using a BP-90 type battery pack 3 CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of fire or electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Connect the battery pack plug to the socket inside the battery case, and insert the battery pack into the case. 1 Remove the battery holder. 5 Label surface <Note> Battery holder Make sure you turn OFF the camera-recorder power before connecting or disconnecting the plug. 2 Attaching the battery case to the camera-recorder. Connect the cable on the camera-recorder to the cable on the battery case (BP-90 type). Using a screwdriver, secure the battery case (BP-90 type) to the camera-recorder. Open the cover and lift the rubber cap so that the screw tightening hole is visible. Tighten the screws to secure the battery case to the camera-recorder. Be sure to fully tighten the screws. 4 Setting the battery type. Select the battery type listed under BATTERY SELECT. Select BATTERY SELECT from the <BATTERY/ P2CARD> screen on the MAIN OPERATION page. Please refer to [8-6-2 BATTERY SETTING1] for more information. <Notes> Do not use excess force when lifting the rubber caps forcibly. Take special care not to pinch the cable. Connect Battery Case (For BP-90 type) 65 Chapter 5 Preparation (continued) Using an NP-1 type battery pack When using a V-mount type battery pack Mount the V-mount adapter plate. Insert the plate and slide it in the direction of the arrow. CAUTION: These servicing instructions are for use by qualified service personnel only. [. . . ] ­C­­­ ID MIX INH ON OFF Remarks Display the software version for the system control microprocessor. 8-9-1 OPTION Items/ Adjustable Data Saved Range ENG SECURITY ON OFF Remarks Select whether or not to prohibit opening the menu screen. Please consult your distributor to release the setting. Select whether or not to inhibit mixing the ID in the camera image. Camera ID setting under VF INDCATOR1 is reflected in the camera image. [. . . ]