User manual PANASONIC AK-HCU931P

[. . . ] Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. CAUTION: This product uses a semiconductor laser system and is a laser class 1 product complies with Radiation Performance Standards, 21CFR SUBCHAPTER J. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Refer servicing to qualified personnel. indicates safety information. 2 Contents Safety precautions . 14 Overview By connecting this unit to the multi-format camera (model AK-HC931P), multi-format images can be input and output. [. . . ] COMM: For connecting the standby INCOM with the system INCOM. INCOM MIC selector switch [MIC] ON: The INCOM microphone is set to ON. OFF: The INCOM microphone is set to OFF. PTTN: The INCOM microphone is set to ON only while the INCOM MIC selector switch is held down. @ Standby INCOM jack This is connected to INCOM 1 line, and it enables calls to be made to the camera's INCOM 1 line. Even when the camera power is OFF, calls can still be made to the camera's INCOM 1 line. 4 Parts and their functions $ Camera control unit rear panel A RET1 B RET2 RET3 RET4 OUT1 C OUT2 OUT3 OUT4/PM Y/G D Pb / B Pr / R PM [ HD SDI INPUT RET1 RET2 RET3 RET4 OUT1 SDI OUTPUT OUT2 OUT3 OUT4 RET1 OUTPUT RET2 PROMPT HD SD E SDI INPUT WFM1 WFM2 PM1 PM2 VBS1 F SDI OUTPUT VBS2 HD SD G INPUT HD REF H 11 22 SD REF SD SD I RTS OUT J OUTPUT CH­1 MIC OUT CH­2 K DIGITAL AUDIO L M N WFM CONTROL CSU / MSU SYNC OUTPUT TRUNK O ROP ALARM AC IN COMMUNICATION IN P U S H V W AUX Z \ ^ GND X P Q R S T U Y ] A Optical fiber connector FXW. 3K. 93C. CLM made by LEMO Pin No. 1 2 3 4 5 6 Function Optical fiber Optical fiber Control wire, hot Control wire, cold AC 240 V live AC 240 V neutral i j i j Polarity Signal flow CAM#CCU CCU#CAM CAM, . CCU CAM, . CCU CCU#CAM CCU#CAM Cable color Yellow (01) Yellow (02) Black Red Orange White E SDTV digital return video 1, 2, 3, 4 input connectors [SDTV DIGITAL RET 1, 2, 3, 4] These connectors are for inputting the return video signals of the SDTV serial digital interface. F SDTV D1 digital video output connectors [SDTV DIGITAL OUT D1 1, 2 3] These connectors are for outputting the D1 format video signals of the SDTV serial digital interface. G Analog return video 1, 2 input connectors [ANALOG RET 1, 2] These connectors (BNC) are for inputting the SD analog return video signals. H PROMPT-IN connectors [PROMPT1, 2] These are the prompter signal input connectors (BNC). Input SDTV composite video signals as the prompter signals. I SDTV waveform monitor output connectors [SDTV WFM 1, 2] These connectors (BNC) are for outputting the camera video signals which are to be displayed on the SDTV waveform monitor. ROP/MSU monitor selection R G B SEQ ENC R G B RGB 3 waveforms Composite video SDTV WFM output B HDTV digital return video 1, 2, 3, 4 input connectors [HD DIGITAL RET 1, 2, 3, 4] (Option) These connectors (BNC) are for inputting the return video signals of the HDTV serial digital interface. C HDTV digital video 1, 2, 3, 4 output connectors [HD DIGITAL OUT 1, 2, 3, 4] (Option) These connectors (BNC) are for outputting the video signals of the HDTV serial digital interface. D HDTV analog component video output connectors [HDTV ANALOG Y/G, Pb/B, Pr/R] (Option) The HDTV analog signals of the camera are output from these connectors (BNC). G/B/R or Y/Pb/Pr video signals can be selected by the master setup unit (MSU) or remote operation panel (ROP). SDTV PM output connector [PM] This is the HDTV PM output (1Vp-p) connector. 5 Parts and their functions $ Camera control unit rear panel A RET1 B RET2 RET3 RET4 OUT1 C OUT2 OUT3 OUT4/PM Y/G D Pb / B Pr / R PM [ HD SDI INPUT RET1 RET2 RET3 RET4 OUT1 SDI OUTPUT OUT2 OUT3 OUT4 RET1 OUTPUT RET2 PROMPT HD SD E SDI INPUT WFM1 WFM2 PM1 PM2 VBS1 F SDI OUTPUT VBS2 HD SD G INPUT HD REF H 11 22 SD REF SD SD I RTS OUT J OUTPUT CH­1 MIC OUT CH­2 K DIGITAL AUDIO L M N WFM CONTROL CSU / MSU SYNC OUTPUT TRUNK O ROP ALARM AC IN COMMUNICATION IN P U S H V W AUX Z \ ^ GND X P Q R S T U Y ] J SDTV picture monitor video output connectors [PM 1, 2] These connectors (BNC) are for outputting the video signals which are to be displayed on the SDTV picture monitor. ROP/MSU monitor selection R G B SEQ ENC SDTV PM1 output Rialarm display Gialarm display Bialarm display Y and skin tone zebra pattern Composite video P INCOM/tally connector [COMMUNICATION] The external INCOM or tally system is connected here. INCOM/tally connector (KPT02E14-19P made by Japan Aviation Electronics Industry) Pin No. Function Shield INCOM 1 INCOM 1 INCOM 1 INCOM 1 INCOM 2 INCOM 2 INCOM 2 INCOM 2 PGM1(H) PGM1(C) PGM2(H) PGM2(C) NC Red tally Green tally NC NC Tally common Contact Contact i j i j i j i j i j i j CCU#SYSTEM CCU#SYSTEM SYSTEM#CCU SYSTEM#CCU CCU#SYSTEM CCU#SYSTEM SYSTEM#CCU SYSTEM#CCU SYSTEM#CCU SYSTEM#CCU SYSTEM#CCU SYSTEM#CCU Polarity Signal flow A B C D E F G H J K L M N P R S T U V K SDTV analog composite video output connectors [SDTV VBS] These connectors (BNC) are for outputting the SDTV analog composite video signals (with sync) of the camera. RTS output connector (HA16RD-3P made by Hirose) Pin No. 1 2 3 Function Common Channel 1 (iDC) Channel 2 Polarity Signal flow S T Mic 1, 2 output connectors [MIC OUT CH-1, CH-2] These are the microphone 1 analog output connectors of the camera. Mic output connector (HA16RD-3P made by Hirose) Pin No. 1 2 3 Function Shield Hot Cold i j CCU#SYSTEM CCU#SYSTEM Polarity Signal flow U Digital audio output connector [DIGITAL AUDIO] This is the camera microphone 1 and 2 output connector (BNC) for AES/EBU digital audio interface specifications. 7 Parts and their functions $ Camera control unit rear panel A RET1 B RET2 RET3 RET4 OUT1 C OUT2 OUT3 OUT4/PM Y/G D Pb / B Pr / R PM [ HD SDI INPUT RET1 RET2 RET3 RET4 OUT1 SDI OUTPUT OUT2 OUT3 OUT4 RET1 OUTPUT RET2 PROMPT HD SD E SDI INPUT WFM1 WFM2 PM1 PM2 VBS1 F SDI OUTPUT VBS2 HD SD G INPUT HD REF H 11 22 SD REF SD SD I RTS OUT J OUTPUT CH­1 MIC OUT CH­2 K DIGITAL AUDIO L M N WFM CONTROL CSU / MSU SYNC OUTPUT TRUNK O ROP ALARM AC IN COMMUNICATION IN P U S H V W AUX Z \ ^ GND X P Q R S T U Y ] W Waveform monitor control connector [WFM CTL] This connector is used for controlling the waveform monitor. [. . . ] O To configure the HD system, the HD output unit (AK-HHD931P), available as an optional accessory, must be installed. SD analog (VBS) RET video Main line HD digital outputs inputs (k2) (k4) (1 output (OUT4) can be Main line HD analog output HD digital RET switched to PM output) (k1: Y, Pb, Pr/G, B, R) Main line SD video inputs (k4) PROMPT signal input outputs (D1k4) (VBSk2) SD digital (D1) Main line SD RET video inputs outputs Install the HD output unit (AK-HHD931P) (k4) (VBSk2) which is an optional accessory. RET1 RET2 RET3 RET4 OUT1 OUT2 OUT3 OUT4/PM Y/G Pb / B Pr / R PM HD SDI INPUT RET1 RET2 RET3 RET4 OUT1 SDI OUTPUT OUT2 OUT3 OUT4 RET1 OUTPUT RET2 PROMPT HD SD SDI INPUT WFM1 WFM2 PM1 PM2 VBS1 SDI OUTPUT VBS2 HD SD INPUT HD REF 1 SD REF 2 SD SD ALARM OUTPUT SYNC OUTPUT CH­2 DIGITAL AUDIO TRUNK WFM CONTROL CSU / MSU ROP AC IN COMMUNICATION IN P U S H RTS OUT CH­1 MIC OUT Handy camera (AK-HC931P) Tally inputs (R, G) NAM Y /C R G B AUX GND FILTER LOCAL MONI SEL OFF PHANT OFF PHANT AB AB ­40 ­30 ­40 ­30 ­20 ­50 ­60 ­20 ­50 ­60 (dB) 1A (dB) MIC2 MIC1 INCOM input/output (ENG, PROD) PGM inputs (PGM1, PGM2) CAM/VTR ON ON GAIN L OW OUTPUT CAM W. BAL B MID BAR A SYNC output for SD monitor system STBY S AV E HIGH TEST PRST SD CARD PTT USER SEL Video Control Video HD sync signal input (tri-level sync) Decide on a valid REF input signal using the internal switch. 1 2 3 4 5 6 MSU cable ROP cable SYNC output for HD monitor system SD sync signal input (black burst: BB) Decide on a valid REF input signal using the internal switch. AUX CSU LINK POWER DC IN 7 8 9 10 11 12 13 14 15 GND MSU connector panel Handy camera + build-up unit (AK-HBU931P) SD WFM SD picture monitor PREVIEW RCP CCU ROP connector panel 12 External dimension drawing RET1 RET2 RET3 RET4 OUT1 OUT2 OUT3 OUT4/PM Y/G Pb / B Pr / R PM HD SDI INPUT RET1 RET2 RET3 RET4 OUT1 SDI OUTPUT OUT2 OUT3 OUT4 RET1 OUTPUT RET2 PROMPT HD SD SDI INPUT WFM1 WFM2 PM1 PM2 VBS1 SDI OUTPUT VBS2 HD SD INPUT HD REF 1 SD REF 2 SD SD ALARM OUTPUT SYNC OUTPUT 459 AC IN COMMUNICATION IN P U S H RTS OUT CH­1 MIC OUT CH­2 DIGITAL AUDIO TRUNK WFM CONTROL CSU / MSU ROP AUX GND 132 13 FUSE 125V 5A OPEN MAIN CABLE SHORT HEAD POWER FUSE 250V 5A ALARM PRIVATE MIC ON SYSTEM LEVEL PTT OFF OFF PGM 2 PGM 1 TALLY/CALL PUSH PGM 424 Camera Control Unit Specifications Power supply: AC 120 V Power consumption: 80 W (when unit is operated on its own) indicates safety information. Video input/output signals SD digital signal (D1) SD analog signal (VBS) HD digital signal (optional) HD analog signal (Y, Pb, Pr/GBR): Output only (optional) PROMPT signal (VBS): Input only Sync input signals HD reference signal (tri-level sync) SD reference signal (BB) (Select one of these signals using the internal switch. ) Audio output signals Analog audio output (MIC 1, 2) Digital audio output (MIC 1, 2) Switch functions Refer to "Parts and their functions" (page 4). Operating temperature range 0 to i40 °C (i32 to 104 °F) Storage temperature range j20 to i60 °C (j4 to 140 °F) Operating ambient humidity Less than 85% Weight Approx. 20. 0 kg (44 lbs) Dimensions (WkHkD) 420k132k459 mm (excluding protrusions) (16-9/16k5-1/4k16-9/16 inches) Rack mounting Attach the rack mounting adapter firmly by using a crosshead screwdriver as follows: Mounting screws (k6) Rack mounting adapter 14 15 PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621 Southeast Region: 1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835 Central Region: 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200 WESTERN ZONE: 3330 Cahuenga Blvd W. , Los Angeles, CA 90068 (323) 436-3500 Government Marketing Department: 52 West Gude Drive, Rockville, MD 20850 (301) 738-3840 Broadcast PARTS INFORMATION & ORDERING: 9:00 a. m. [. . . ]