User manual PANASONIC AK-MSU930P

[. . . ] Master Setup Unit AK-MSU930P Before attempting to connect, operate or adjust this product, please read these instructions completely. Safety precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] DARK: Dark detail This function boosts the detail in the dark parts. CORNER: Corner detail This function boosts the detail around the edges of the screen. SOURCE: Detail source This is used to select the source signals for creating the detail components. +CLP: Detail edge overshoot clip This is used to limit the length of the overshoot parts of the detail edge components. ­CLP: Detail edge undershoot clip This is used to limit the length of the undershoot parts of the detail edge components. DTL +KNEE: Detail edge overshoot knee This function applies the knee to the detail edge overshoot parts. DTL ­KNEE: Detail edge undershoot knee This function applies the knee to the detail edge undershoot parts. KDTL: Knee detail This is used to boost detail components of the parts where the knee has been applied. KDTL CRSP: Knee detail crisp This is used to remove the very faint noise components below the level set from the knee detail components. KDTL FREQ: Knee detail boost frequency This is used to select the knee detail boost frequency. KDTL +CLP: Knee detail edge overshoot clip This is used to limit the length of the overshoot parts of the knee detail edge components. KDTL ­CLP: Knee detail edge undershoot clip This is used to limit the length of the undershoot parts of the knee detail edge components. KDTL +KNE: Knee detail edge overshoot knee This function applies the knee to the knee detail edge overshoot parts. KDTL ­KNE: Knee detail edge undershoot knee This function applies the knee to the knee detail edge undershoot parts. HD skin tone detail switch [HD. SKIN] This is used to apply coring to the detail enhancement of the skin tone areas in the HDTV video signals to soften the skin tone detail enhancement. It cannot be selected when the lamp of the HD detail OFF switch is lighted. SKIN ZEB: Skin tone area zebra This is used to set whether to apply the zebra pattern to the areas where coring is applied as the skin tones to the Y signals in the PM output. PHASE: Skin tone area phase This is used to move the areas to be recognized as the skin tones in the range of 153 to 93 along the Q axis on the color vector display. WIDTH: Skin tone area width This is used to widen the areas to be recognized as the skin tones in the range of 1 to 20 along the I axis on the color vector display. CRISP: Skin tone detail crisp This is used to remove the very faint noise components from the skin tone detail components. SKIN LVL: Skin detail level This is used to set the chroma saturation of the parts where the skin tone detail is applied. SDTV detail control switch [SD. DTL CONTROL] This switch is selected to change the amount by which the picture quality in the detailed parts of the SDTV video output has been enhanced (by which the relative hardness/softness has been adjusted). [. . . ] Green tally indicator This lights when the green tally signal is input to the tally INCOM connector on the CCU. Q Active switch [ACTIVE] When this is pressed during the iris and the master pedestal function priority display, the iris and the master pedestal function priority changes, and the lamp of the switch lights. When the ACTIVE switch on the ROP is pressed, the iris priority is transferred to the ROP. R Master pedestal level indicator This indicates the master pedestal level. Variable range: ­99 to 99 I Auto iris switch [AUTO] This is used to activate the auto iris function. Lighted: The auto iris mode is established. [. . . ]