User manual PANASONIC AW-PH360N

[. . . ] Indoor Pan/Tilt Head AW-PH360N Before attempting to connect, operate or adjust this product, please read these instructions completely. Printed in Japan F0505Y0 D VQTB0085 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. WARNING: HAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER CHANGE OF SWITCH SETTING INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL. 1 indicates safety information. [. . . ] · Use a 10BASE-T straight cable (UTP category 5) to connect the unit's CONTROL IN IP/RP connector with the controller's PAN TILT CONTROL OUT connector. · Use a coaxial cable (BELDEN 8281) to connect the unit's CAMERA CONTROL IN connector with the controller's CAMERA CONTROL OUT connector. · Use a coaxial cable to connect the unit's Pr/SDI OUT connector with the color monitor's SDI input connector. · Check that the pan/tilt head and camera can be controlled by the controller. - 29 - Connections 4When the camera and pan/tilt head are to be controlled by the AW-RP505 control panel for transmitting composite signals Genlock signals must be supplied if a multiple number of cameras and pan/tilt heads are to be used. Camera cable (supplied) Preview color monitor 10BASE-T (equivalent to UTP category 5) straight cable, max. (10 m) Coaxial cable Multi hybrid control panel: AW-RP505 DC cable (UL Type SPT-2 2!16 AWG or UL Type NISPT-2 2!16 AWG, to be locally purchased) 10BASE-T (equivalent to UTP category 5) straight cable, max. (500 m) Coaxial cable (BELDEN 8281), max. (10 m) AC adapter: AW-PS300A Multiport hub: AW-HB505 Color monitor Coaxial cable (BELDEN 8281), max. (500 m) · Use the supplied camera cable to connect the unit with the convertible camera. · Set controller selection switch SW1 to the right side (RP501), and select the transmission signal selection setting that supports the analog/IEEE1394 card. · Use a 10BASE-T straight cable (UTP category 5) to connect the unit's CONTROL IN IP/RP connector with the multiport hub's PAN/TILT CONTROL OUT connector. · Use a coaxial cable (BELDEN 8281) to connect the unit's CAMERA CONTROL IN connector with the multiport hub's CAMERA CONTROL OUT connector. · Use a coaxial cable (BELDEN 8281) to connect the unit's VIDEO OUT connector with the multiport hub's VIDEO IN connector. · Use a 10BASE-T straight cable (UTP category 5) to connect the multiport hub's PAN/TILT CONTROL IN connector with the controller's PAN/TILT CONTROL OUT connector. · Use a coaxial cable (BELDEN 8281) to connect the multiport hub's CAMERA CONTROL IN connector with the controller's CAMERA CONTROL OUT connector. · Use a coaxial cable (BELDEN 8281) to connect the multiport hub's PREVIEW OUT connector with the controller's PREVIEW IN connector. · Connect the multiport hub's VIDEO OUT connector to the color monitor's VIDEO input connector. · Check that the pan/tilt head and camera can be controlled by the controller. - 30 - Connections 5When the camera and pan/tilt head are to be controlled by the AW-RP505 control panel for transmitting component signals Genlock signals must be supplied if a multiple number of cameras and pan/tilt heads are to be used. Camera cable (supplied) Color monitor Coaxial cable Multi hybrid control panel: AW-RP505 10BASE-T (equivalent to UTP category 5) straight cable, max. (10 m) DC cable (UL Type SPT-2 2!16 AWG or UL Type NISPT-2 2!16 AWG, to be locally purchased) 10BASE-T (equivalent to UTP category 5) straight cable, max. (500 m) Coaxial cable (BELDEN 8281), max. (10 m) AC adapter: AW-PS300A Coaxial cable (BELDEN 8281), max. [. . . ] Replace the battery once it has lost its effectiveness. (The pan/tilt head uses a CR2032 manganese dioxide-lithium battery. ) Removing the battery 1. Remove the four cover screws, and remove the head cover. Press the battery in the direction shown by the arrow in the figure, and slide it. [. . . ]