User manual PANASONIC AW-PS505

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER CHANGE OF SWITCH SETTING INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL. Note: The rating plate (serial number plate is on the bottom of the unit. The information marking of this product may be found on the bottom of the unit. [. . . ] When a switch is pressed, it lights to indicate that the corresponding signal is selected. Depending on the operation mode, the switches may light with full or half brightness. Full brightness: When the selected input is being output to PGM OUT. Half brightness: When the switch is selected but the selected input is not being output to PGM OUT. [Example] When the Fader Lever is at the A-bus side, the A-bus signals are output so that the A-Bus Input Selection Switches will light with full birghtness, but the B-bus signals are not output so that B-Bus Input Selection Switches will light with half brightness. w Freeze indicator [FRZ] This LED lights to indicates that the VIDEO IN 5 signal is frozen. Bear in mind that since the image remains frozen while it is lighted, the switcher output will not change even when the input signal has changed. e Input 5/FMEM Selector Switch [FMEM] This is used to select the signal which has been input to VIDEO IN 5 or the internal frame memory. When the switcher is used for the first time and the frame memory has been selected, the factory setting screen is output. By transferring image data from a personal computer to the frame memory, the images and text created by the user can be output. For details, refer to the page on which image transfer is described. During an auto take operation, no manual operations will be performed even if the Fader Lever i is moved. Caution In using the Auto Take function, be sure to move Fader Lever i all the way to A or B. Auto Take will not work unless the lever is fully moved to A or B. i Fader Lever [A/B] This lever is used to switch the signal selected with A-Bus Input Selection Switch } to the signal selected with B-Bus Input Selection Switch q or vice versa by the wipe or mix effect. When the lever is moved from A to B, the video signal is also switched from A to B accordingly. Similarly, when the lever is moved from B to A, the video signal is switched from B to A. o Bus Tally Indicators [A], [B] These indicate the output statuses of the A-bus and B-bus. The [A] or [B] LED lights to indicate that A-bus or B-bus signals are being output. [Examples] · [A] lights when the Fader Lever is at the A side since only the A-bus signals are output. · Both [A] and [B] light when the Fader Lever is between the A and B sides since both A-bus and B-bus signals are output. Note Bus control based on the flip-flop system is enabled by changing the setting of the bus selector switch [BUS A/B /F. F. ]R which is one of the Setup Switches K. [. . . ] The actual time taken will depend on the performance of the host computer. Fig. 13 Memory selection 6 Click the "Write USB" button to start transferring the image data. After the completion of the transfer, monitor the AW-PS505's PGM output and check that the image data has been transferred. (Fig. 14) AW-PS505 program output Click the button Fig. 14 PGM check 30 31 CONNECTIONS qFor installation and connection, be sure to ask the store where you purchased the product. qBefore making any connection, switch off all the components of the system. [. . . ]