User manual PANASONIC AW-CB400N

[. . . ] Remote Operation Panel AW-CB400N Before attempting to connect, operate or adjust this product, please read these instructions completely. Printed in Japan F1104S0 D VQTB0045 Safety precautions FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] AUTO: The cameras automatically adjust the lens iris in accordance with the light quantity, and the button lamp lights. MANU: The lens iris is adjusted manually using the (I) IRIS dial. At this setting, the button lamp is off. LOCK: The lens iris is locked at the manually adjusted setting. It cannot be adjusted even by turning the (I) IRIS dial. When the (I) IRIS dial is turned, the button lamp flashes to indicate that the lens iris cannot be adjusted. When the ROP is connected to the pan/tilt control panel, the lens iris control can be set to "From pan/tilt control panel only", "From ROP only" or "From both", depending on the setting selected by the pan/tilt control panel. For further details, refer to the instruction manual of the pan/tilt control panel. H CALL button When this button is pressed, the buzzer of the connected controller sounds, and the button lamp lights. I IRIS dial The lens iris can be adjusted by turning this dial while the (B) IRIS [AUTO/MANU/LOCK] button is set to MANU. The iris is opened by turning the dial clockwise and stopped by turning it counterclockwise. By pressing the (C) CONT dial, the response speed can be switched from "fast" to "slow" or vice versa. J FAST/SLOW lamp When the response speed of the (I) IRIS dial is at "fast", this lamp lights up; when it is at "slow", the lamp is off. C CONT dial Use this for menu setting operations. D OPERATE lamp When the (E) OPERATE switch is at ON, this lamp lights up green; when it is at OFF, the lamp is off. E OPERATE [OFF/ON] switch Camera control is enabled by setting this switch to ON. Note When the ROP is connected to the pan/tilt control panel, camera control is not possible unless the OPERATE switch on the pan/tilt control panel is set to ON. 8 Parts and their function $ Rear panel K L M N O K CONTROL OUT TO CONTROL PANEL connector When connecting the pan/tilt control panel for operation, connect this connector to the CAMERA CONTROL IN FROM ROP connector on the pan/tilt control panel using the control panel's connecting cable. The cameras are then controlled through the pan/tilt control panel. M CONTROL OUT TO CAMERA connectors [1] to [5] Connect these to the convertible cameras. Use the connecting cables (optional accessory) AW-CA50T8 or AW-CA50T9 + RS-422/RS-232C converter to connect these connectors to the I/F REMOTE connectors on the convertible cameras. N DC 12V IN socket L TALLY/INCOM connector Connect this to the TALLY/INCOM connector on the video switcher or other units. When the TALLY connector is set to the GND level, the (1) TALLY lamp lights. Do not apply a voltage in excess of 5V to this connector. Pin No. 1 9 2 10 3 11 4 12 5 13 6 14 7 15 8 Signal Name TALLY1 TALLY2 TALLY3 TALLY4 TALLY5 TALLY GND ­­­ ­­­ ­­­ ­­­ MIC + MIC ­ INCOM GND SP ­ SP + Connect the AW-PS505 AC adaptor (optional accessory) to this socket. When the ROP is connected to the pan/tilt control panel using the pan/tilt control panel connecting cable, power will be supplied to the ROP from the pan/tilt control panel. O Grounding terminal Connect this terminal to ground. 87654321 ?>=<;:9 Pin layout as seen from the back panel of AW-CB400 Use the accessory tally/INCOM connector (D-SUB 15-pin) to connect the tally/INCOM signals to the system. Connect a 4-wire INCOM system to the INCOM connector. When the ROP has been connected to the pan/tilt control panel, the tally/INCOM functions of the ROP and the pan/tilt control panel will be executed if the tally/INCOM signals are connected to the ROP or the pan/tilt control panel. 9 Connections $ When connecting a convertible camera directly · First, turn off the power of all the equipment before proceeding with the connections. · Use the AW-PS505 for the AC adaptor of the ROP. Connect the DC 12V OUT socket on the AW-PS505 to the DC 12V IN socket on the ROP using the DC cable provided with the AW-PS505. · Use the AW-PS505 for the AC adaptor of the convertible camera. Connect the DC 12V OUT socket on the AW-PS505 to the DC 12V IN socket on the convertible camera using AW-CA4T1. [. . . ] The lamp of the button lights when the filter is set to 1/64ND; it is off when another filter is selected. 1/64 ND: BUZZER setting (OFF/ON) This is used to set for the buzzer inside the remote operation panel to ON or OFF. The buzzer does not sound at the OFF setting. The buzzer sounds when the CALL button is pressed. 19 How to mount the ROP in a rack <NOTE> The AW-CB400 is 100 mm wide. If it is to be installed in a full-size rack (which accommodates units totaling 420 mm in width), provide panels or other parts to supplement the AW-CB400's width so that it will fill the rack width-wise. [. . . ]