User manual PANASONIC AW-DU600P

[. . . ] Dial Up Adapter Model AW- P Before attempting to connect, operate or adjust this product, please read these instructions completely. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Press the MENU+ key ( 2 i START ) to change the menu setting item. When "Menu-5 Output-1" appears on the LCD panel, STOP use the !START # keys and select RS-2332C or RS-422 according to operating conditions. Menuj 5 Outputj 1 RSj 232C RSj 422 When the settings are completed, press the MENU+ key ( 2 i START ) once again to exit the menu settings. 11 Connections Making a call Make a call from the AW-DU600 of the transmitting system. 5. 1. Use the number keys on this adapter to enter the desired number. The telephone number entered appears on the top section of the LCD panel. !Telephone number entered 0123456789 1: Press Start If the wrong number is entered by mistake, press the DELETE key ( # i 0 ) to delete 1 digit at a time, starting from the number entered last. Press the CLEAR key ( # i START ) to delete the whole number at once. After control of the pan-tilt head is completed, press the STOP key. "Hang Up" appears on the LCD display and the telephone line is cut. Once the line is cut, "Press Start" appears on the LCD panel. When ON has been selected for the "Menu-7 Pw-Off" setting, the power to the pan-tilt head will turn off at the same time as the telephone line is cut. When OFF has been selected for the "Menu-7 Pw-Off" setting, the power to the pan-tilt head will remain on when the telephone line is cut. <Note> If the POWER switch or OPERATE switch on the control panel is set to OFF before the telephone line is cut, the power to the pan-tilt head will turn off regardless of the "Menu-7 Pw-Off" setting. 3. After entering the telephone number, press the START key. When the connection is initiated, "Calling" appears on the LCD panel. When the connection is established, "Connect" appears on the LCD panel and control of the pan-tilt head system from the control panel is possible. <Note> The message appearing on the LCD panel may differ, depending on the modem used. Control the pan-tilt head system from the control panel. When an AW-RP605 is being used as the control panel, set the OPERATE switch to ON to control the pan-tilt head system. <Note> OWhen an AW-RP505 or AW-RP605 is being used as the control panel, it is possible to switch the receiving pan-tilt head system using the CONTROL button on the control panel. OIf the OPERATE switch on the AJ-RP605 is set to ON before the telephone line is connected, "NO CONNECT" is displayed on the LCD panel. <Note> While the telephone line is being connected, none of the operating keys on the adapters will function except for the STOP key on the transmitting side. 4. 12 Connections $ Direct mode 1. Control the pan-tilt head system directly using this adapter: AW-DU600 AW-PS301 AW-CA50T29 (composite) AW-CA50C29 (component) Convertible camera 10 Base-T cable AW-PH350 AW-PS300 13 Connections Connection procedure 1. 3. Connect the pan-tilt head system to the CONTROL OUT connector on this adapter. Turn on the power to this adapter and the pan-tilt head system. Dial Up Adapter settings 1 Set this adapter to direct mode. [. . . ] Press the RECALL key ( # i STOP ). O Registering a telephone number 1. Enter the number using the operating keys on this adapter. While pressing the # key, press one of the dial memory registration keys from 1 (M1) through 5 (M5) into which the number is to be entered. "Writing Memory 2" (2 is the dial memory number) appears on the LCD panel and the telephone number is stored. 2. [. . . ]