User manual PANASONIC AW-E300A

[. . . ] Convertible Camera AW-E300AP (Lens : Optional accessory) Before attempting to connect or operate this product, please read these instructions completely. For U. S. A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] (painting setting in only USER MODE. ) [ADJUSTMENT by CAMERA] Press the YES/ABC Switch for over 2 seconds and the black balance will be set automatically in 10 seconds. -23- YES/ABC Switch + NO/BAR IRIS ­ DC12V IN AUTO LED AUTO/ATW ATW A B R PAINTING GAIN B TOTAL PED R PED B AUTO AUTO set switch ABC AWC HOLD ABC s TOTAL PEDESTAL LEVEL ADJUSTMENT (Use an oscilloscope or a waveform monitor for this adjustment. ) This step is to adjust the black levels (pedestal levels) of two or more cameras to be the same. Select Pedestal item in the brightness setting Sub Menu (Select [Pedestal] in the [Iris, Shutter, Gain Set] sub menu in USER MODE. ) 3. Set the pedestal level to 5 IRE (0. 035 V) with the YES/ABC switch or the NO/BAR switch. **Brightness Set** Picture Level Light PEAK/AVG Light Area Top Auto ND ELC) Auto Gain Up Manu Gain Up Pedestal Contrast(Gamma) Return ±0 0 cut OFF OFF 0dB ±0 MID OPTION CARD MENU ITEM/AWC YES/ABC VIDEO OUT I/F REMOTE G/L IN + NO/BAR IRIS ­ DC12V IN 5 IRE (0. 035 V) NO/BAR switch YES/ABC switch [ADJUSTMENT with RCU (RCB, Hybrid control panel)] Adjust the pedestal level to 5 IRE with the total pedestal adjustment. AUTO/ATW ATW A B R PAINTING GAIN B TOTAL PED R PED B AUTO AWC HOLD ABC TOTAL PEDESTAL -24- s GEN-LOCK ADJUSTMENT Phase adjustments must be performed with the camera or the RCU (RCB) when external synchronizing signals are supplied to the system in cases where multiple cameras are used or peripheral devices are connected. **G/L. Color Bar Set** H Phase ±0 SC Coarse 1 SC Fine ±0 Color Bar Set 7. 5IRE OPTION CARD MENU ITEM/AWC YES/ABC G/L IN VIDEO OUT I/F REMOTE + NO/BAR IRIS ­ DC12V IN q HORIZONTAL PHASE CONTROL Observe the waveform of the external synchronizing input signal (black burst signal) and video output signal on a two-channel oscilloscope. Then match the horizontal phase of both signals by adjusting them with the cameras or RCU's horizontal phase control. External gen-lock input signal (black burst output of special effect generator) Return NO/BAR switch YES/ABC switch [ADJUSTMENT with RCU (RCB, Hybrid control panel )] Use the horizontal phase control. ENC OFF Video signal Adjust the horizontal phase PAGE VF USER SET H. PHASE ON ITEM UP DOWN SC PHASE COARSE FINE 270° 180° 0° 90° [ADJUSTMENT by CAMERA] 1. Press the NO/BAR switch for over 5 seconds to display the color bar. Color Bar Set] on the main menu, then select [H PHASE] on the submenu. Adjust the horizontal phase with the YES/ABC and NO/BAR switch. -25- Horizontal phase control Subcarrier phase fine control Subcarrier phase coarse control CAUTION: When horizontal phase adjustment is required using RCU (RCB) or Hybrid Control Panel, BAR/CAM switch should be set to BAR. Horizontal phase cannot be adjusted if the switch is in the CAM position. After adjustment set BAR/CAM switch back to CAM. q COLOR PHASE ADJUSTMENT Supply the output signal (split color bar) from the color special effect generator to a color monitor or vectorscope. Adjust the color phase of the camera. Magenta 4. Perform fine adjustment with the YES/ABC switch and the NO/BAR switch. **G/L. Color Bar Set** H Phase ±0 SC Coarse 1 SC Fine ±0 Color Bar Set 7. 5IRE Yellow Green White Cyan Blue Red Color bar of camera Sprit line Return [ADJUSTMENT by CAMERA] 1. Press the NO/BAR switch for over 5 seconds for the color bar mode. Color Bar Set] on the main menu, then select [SC Coarse] on the sub menu. Make coarse adjustment with the YES/ABC switch and the NO/BAR switch. -26- Red Color bar of special effects generator [ADJUSTMENT with RCU (RCB, Hybrid control panel)] Use the subcarrier phase coarse adjustment control and subcarrier phase fine control. * It is recommended that a vectorscope be used for maximum accuracy in color phase adjustment. CAUTION: When color phase adjustment is required using RCU (RCB) or Hybrid Control Panel, BAR/CAM switch should be set to BAR. Color phase cannot be adjusted if the switch is in the CAM position. After adjustment set BAR/CAM switch back to CAM. Magenta Yellow Green White Black Cyan Blue USE MODE SETTING s Use Mode Setting The camera has four use modes, and various functions for four use modes have been preset. Functions can be set as best suited to each use mode. [. . . ] %9 White Clip Level Setting [White Clip: 95 % - 110 %] The peak level of video signals to be white-clipped can be set. -45- ^0 Flare Correction Level Setting [Flare R/G/B: 0 - 100] Flare correction level can be adjusted. * Flare correction level has already been adjusted prior to shipment from the factory. ^1 Black Stretch Setting [Black Stretch: ON/OFF] Black stretch to correct the suppression of black portions at low luminance can be set to ON or OFF. ^2 Clean DNR Setting [Clean DNR: HIGH/LOW/OFF] Clean DNR effect can be selected. [. . . ]