User manual PANASONIC AW-E650

[. . . ] Convertible Camera AW-E750 AW-E655 AW-E650 AW-E350 AW-E750 AW-E655 AW-E650 AW-E350 Before attempting to connect, operate or adjust this product, please read these instructions completely. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] From RCU (RCB): Set the user set switch in the pocket to the ON position. The main menu appears on the monitor screen. Each time the MENU switch (A), ITEM/AWC switch (S), or NO/BAR switch (-) is pressed, the blinking item moves up or down. When the YES/ABC switch is pressed after selecting the desired item to blink, the submenu for the selected item appears on the screen. Select the desired item to be changed in its settings using the the MENU switch (A) and ITEM/AWC switch (S). Press the YES/ABC switch (+) or NO/BAR switch (­) to change the settings. Select [Return] using the MENU switch and ITEM/ AWC switch, then press the YES/ABC switch to return to the main menu. After changing the settings, take the following steps. Camera alone: Select [End] using the MENU switch and ITEM/AWC switch and press the YES/ABC switch. -32- RCU (RCB): Set the user set switch in the pocket to the OFF position. The camera will now operate according to the new settings. CAMERA MENU ITEM/AWC YES/ABC NO/BAR RCU (RCB) USER SET SWITCH s SUB MENU (Halogen Mode, Fluorescent Mode, Outdoor Mode) 1 Brightness Set Display ±0 0 Top Cut (OFF) (OFF) (---) (0dB) 0dB OFF (±0) 3 G/L Adjustment Set Display **G/L Adjustment Set** H Phase (±0) SC Coarse ( 1) SC Fine (±0) Color Bar Set 7. 5IRE 5 Other Set Display **Other Set** **Brightness Set** 1 ------- Picture Level 2 ------- Light PEAK/AVG 3 ------- Light Area 4 ------- Auto ND(ELC) 5 ------- Auto Gain Up 6 ---------- AGC Max Gain 7 ------- Manual Gain Up 8 ------- Digital Gain Up 9 ------- Charge Time 10 ------- Pedestal 1 ------2 ------3 ------4 ------- Mid 1 ------- Contrast(Gamma) (OFF) 2 ------- Shutter Speed --3 --------- Synchro Scan 4 ------- V Resolution Normal 5 ------- Baud Rate 9600bps 6 ------- Component Y/Pr/Pb 7 ------- Digital Extender OFF 8 ------- Fan Auto 9 ------- Auto Focus OFF 10 ------- Filter Normal Return Return Return 2 Color Set Display **Color Set** ±0 ±0 (AWC A) --Posi 4 Sharpness (DTL) Set Display **Sharpness(DTL) Set** 1 ------- Chroma Level 2 ------- Flesh Tone 3 ------- White Bal 4 ---------- ATW Speed 5 ------- Nega/Posi Sharpness 1 ------- DTL Select (High) 2 --------- Level OFF 3 ------- Noise Suppress OFF 4 ------- Clean DNR OFF 5 ------- 3D-DNR 6 ------- DTL Flesh Tone Mid Return Return · Settings enclosed in parentheses can be set with the RCU (RCB) switch or VR in RCU (RCB) mode. · To return to the initial settings, refer to page 56. -33- s Setting and Changing of the Setting (Halogen Mode, Fluorescent Mode, Outdoor Mode) 1 Brightness Set Display 1. Video Level Adjustment [Picture Level: ­50 to +50] Convergence level of AUTO IRIS/AUTO GAIN UP/ AUTO ND (ELC) can be adjusted. Detecting Ratio Adjustment [Light PEAK/AVG: P50 to A50] The ratio of AUTO IRIS/AUTO GAIN UP/AUTO ND (ELC) detected peak to average can be adjusted within a predetermined range. Photometric Measurement Method Setting [Light Area: All, Center, Top cut, BTM cut, R/L cut] A photometric measurement method can be selected for AUTO IRIS/AUTO GAIN UP/AUTO ND (ELC). Center: The screen is measured mainly in the center area, about one-third of both the top and bottom and one-third of both the right and left portions of the screen are excluded from measurement. Top cut: About one-third of the top part of the screen is excluded from measurement. BTM cut: About one-third of the bottom portion of the screen is excluded from measurement. R/L cut: About one-third of both the right and left portions of the screen are excluded from measurement. 4. Auto ND (ELC) Setting [Auto ND (ELC): ON, OFF] This cannot be set unless either "OFF" or "Auto" has been set for the CCD storage time setting (1-9). ON: The electronic shutter is controlled to automatically adjust the luminance. OFF: Luminance is not automatically adjusted by the electronic shutter. Notes · ON is automatically selected when the electronic shutter (5-2) on the submenu [Other Set] is set to [Auto ND]. OFF is selected when other than [Auto ND] is selected. [. . . ] The safety zone and center marker indicate electrical positions and, as such, they may be at variance with their optical positions. 4. EVF Output Setting [EVF Output: Y, CVBS] This is used to set the signals to be output to the viewfinder. Y: The luminance signal is output to the viewfinder. CVBS: The color signals are output to the viewfinder. [. . . ]