User manual PANASONIC AW-HB605

[. . . ] The multi control hub may malfunction if it is dropped or exposed to strong shocks. O Use within a temperature range of 14°F to 113°F (­10°C to +45°C). Using the multi control hub in environments colder than 14°F (­10°C) or hotter than 113°F (+45°C) could have a damaging effect on the internal components. O Connect and disconnect cables only when the power is turned off. [. . . ] ; Black Burst Output [BLACK BURST OUT] (BNC Connector) This is the output jack for the reference signal generator built into the multi control hub. This signal may be used as the reference signal for peripheral equipment that uses external synchronization. 8 9 Controls and Their Functions $ Priority Switchbox System Connections (Indoor Pan/tilt Head System) O Turn off the power to all pieces of equipment before making any connections. O For the control panel, use the AC adapter model AW-PS301 (sold separately), for the multi port hub and multi control hub, the AC adapter model AW-PS505 (sold separately), and for the pan/tilt head AC adapter model, the AWPS300 (sold separately). O Use an AW-PH300 series pan/tilt head and a camera from the convertible camera series. Use camera cable AW-CA50 T15 (sold separately) to make connections between the pan/tilt head and camera. O Connect the pan/tilt head (AW-PH300) to its AC adapter (AW-PS300) using a DC power cord (cable conforming to the Electrical Equipment Handling Law and with a nominal cross-sectional area of 1. 25 mm2 or more, to be obtained locally). The maximum cable distance between the pan/tilt head and its AC adapter is 30 meters. O Connect the multi control hub to its AC adapter (AW-PS505). O Connect the multi port hub to its AC adapter (AW-PS505). O Connect the control panel (AW-RP301, AW-RP305, AW-RP501, AW-RP505) to its AC adapter (AW-PS301). Use a cord clamper to secure the DC cord of the AC adapter and prevent the DC plug from coming loose accidentally. O Connect the pan/tilt head and the convertible camera using the AW-CA50 T15 camera cable. O Connect the electric zoom lens iris control cable to the camera and the remote (zoom and focus control) cable to the pan/tilt head. Cord clamper < < Priority Switchbox Contacts (Terminal Panel) These are the output contacts of the priority switchbox. They should be connected to the TALLY terminals on the control panel. Make connections using cable conforming to the Electrical Equipment Handling Law and with a nominal cross-sectional area of 0. 128 mm2 (wire number AWG26) or more. The maximum cable length (distance between priority switchbox and control panel) is 10 meters. The connection terminals differ depending on the control panel model. The correct connection terminals are listed below. AW-RP305: Any of terminals TALLY 1 through TALLY 5 and the GND terminal. Turn the power on. Turn on the power control switches of the AC adapters of the pan/tilt heads and control panels, as well as the AC adapter and power control switch of the multi control hub. [. . . ] 4 Mount the multi control hub in the rack and secure it in place using four rack mounting screws (part number W2MSS/5008). Feet Mounting screws Power switch Specifications Power supply: DC +12 V (4-pin Cannon Connector) Power consumption: DC 12 V, 0. 47 A Video input: Composite video 1 V [p-p] 75 a1 (BNC connector) Camera control inputs: Control signal (BNC connector) a5 Pan/tilt head control inputs: Control signal (RJ-45 8-pin modular jack) a5 Preview video outputs: Composite video 1 V [p-p] 75 a5 (BNC connector) Black burst outputs: 75 a6 (BNC connector) Camera control output: Control signal (BNC connector) Pan/tilt head control output: Control signal (RJ-45 8-pin modular jack) Switch function: Power on/off Control panel connecting cables: Number of connecting cables: 4 (3 coaxial cables, 1 10BASE-T straight cable); 5 sets (when using G/L function) Pan/tilt head connecting cables: 4 connecting cables per pan/tilt head (3 coaxial cables, 10BASE-T straight cable) (when using G/L function) Maximum cable length: Length of cable from camera and pan/tilt head to control panel: Max. 500 m (assuming: coaxial cable: 5C-2V, 10BASE-T straight cable: UTP category 5) Operating temperature range: +14°F to +113°F (­10°C to +45°C) Dimensions (WaHaD): Body: 16 9/16a3 1/2a9 7/8 (420a88a250 mm) Priority switchbox: 2 13/16a3 1/2a1 7/16 (70a88a35 mm) Weight: Approx. 12. 32 lb (5. 6 kg) Finish: Cover: Steel panel with AV ivory color polyvinyl chloride finish (approximate color: Munsell 7. 9Y 6. 8/0. 8) Panel: AV ivory color paint (approximate color: Munsell 7. 9Y 6. 8/0. 8) Rack mounting bracket Rack mounting screws W2-MSS/5008 (Option) Switchbox To mount the switchbox on a rack, use the supplied rack mounting brackets and mounting screws (M4a8). Rack mounting bracket Mounting screws <Notes> O Rack mounting screws sold separately (part number W2-MSS/5008). O To ensure that the temperature within the rack does not exceed +113°F (+45°C), make sure to provide sufficient space (a minimum of one chassis width between units) between the multi control hub and the other pieces of equipment mounted in the rack or install a cooling fan. Weight and dimensions indicated are approximate. [. . . ]