User manual PANASONIC AW-LZ10MD

[. . . ] -2- FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] (500 m) Hybrid control panel: AW-RP501 · Use the supplied camera cable to connect the unit with the convertible camera. · Set controller selection switch SW1 to the right side (RP501), and select the transmission signal selection setting that supports the analog/IEEE1394 card. · Use a 10BASE-T straight cable (UTP category 5) to connect the unit's CONTROL IN IP/RP connector with the controller's PAN TILT CONTROL OUT connector. · Use a coaxial cable (BELDEN 8281) to connect the unit's CAMERA CONTROL IN connector with the controller's CAMERA CONTROL OUT connector. · Use coaxial cables to connect the unit's Y OUT connector, Pr/SDI OUT connector and Pb OUT connector with the component input connectors on the color monitor. · Check that the pan/tilt head and camera can be controlled by the controller. · Transmitting component signals over a long distance requires a separate cable compensation unit. - 28 - Connections 3When the camera and pan/tilt head are to be controlled by the AW-RP501 control panel for transmitting SDI signals Coaxial cable Camera cable (supplied) Coaxial cable (BELDEN 8281), max. (200 m) Color monitor Coaxial cable (BELDEN 8281), max. (500 m) DC cable (UL Type SPT-2 2!16 AWG or UL Type NISPT-2 2!16 AWG, to be locally purchased) AC adapter: AW-PS300A 10BASE-T (equivalent to UTP category 5) straight cable, max. (500 m) Hybrid control panel: AW-RP501 · Use the supplied camera cable to connect the unit with the convertible camera containing the plugged-in SDI card (such as the AW-PB504N). · Use a coaxial cable to connect the SDI card's SDI OUT connector with the unit's SDI IN connector. (500 m) Coaxial cable (BELDEN 8281), max. (10 m) AC adapter: AW-PS300A Coaxial cable (BELDEN 8281), max. (500 m) Multiport hub: AW-HB505 · Use the supplied camera cable to connect the unit with the convertible camera. · Set controller selection switch SW1 to the right side (RP501), and select the transmission signal selection setting that supports the analog/IEEE1394 card. · Use a 10BASE-T straight cable (UTP category 5) to connect the unit's CONTROL IN IP/RP connector with the multiport hub's PAN/TILT CONTROL OUT connector. · Use a coaxial cable (BELDEN 8281) to connect the unit's CAMERA CONTROL IN connector with the multiport hub's CAMERA CONTROL OUT connector. · Use a 10BASE-T straight cable (UTP category 5) to connect the multiport hub's PAN/TILT CONTROL IN connector with the controller's PAN/TILT CONTROL OUT connector. · Use a coaxial cable (BELDEN 8281) to connect the multiport hub's CAMERA CONTROL IN connector with the controller's CAMERA CONTROL OUT connector. · Use coaxial cables to connect the unit's Y OUT connector, Pr/SDI OUT connector and Pb OUT connector with the component input connectors on the color monitor. · Check that the pan/tilt head and camera can be controlled by the controller. · Transmitting component signals over a long distance requires a separate cable compensation unit. - 31 - Connections 6When the camera and pan/tilt head are to be controlled by the AW-RP505 control panel for transmitting SDI signals Genlock signals must be supplied if Coaxial cable a multiple number of cameras and pan/tilt heads are to be used. Camera cable (supplied) Color monitor Coaxial cable (BELDEN 8281), max. [. . . ] To release the setting: While holding down the MENU/LIMIT button on the controller, press PRESET MEMORY button 10 . The setting is released when the lamp of the PRESET MEMORY button 50 comes on. - 46 - Replacement of consumable parts $ Replacing the battery The battery lasts for about 5 years. The pan/tilt head stores the preset positions, limiter positions and other data in its memory. Although this data is retained even after the power has been turned off, it will be lost when the power is turned off once the battery has reached the end of its service life. [. . . ]