User manual PANASONIC AW-PB306P

[. . . ] . 10 Overview Installing the SDI card in a convertible camera (such as the AW-E300, AW-E600, AW-E800A) and mounting the camera on the interface bracket makes it possible for a viewfinder and/or intercommunications headset to be used and thus enable the camera to be used as a studio camera. It is also possible to output SDI signals which are compliant with the SMPTE259M standard. Features O SDI signal output compliant with SMPTE259M standard (max. 200 m using a BELDEN 9231 coaxial cable) O An inter-communications headset can be used and its volume adjusted O Includes viewfinder STANDBY/ON switch O Output signals (brightness and composite video signals) to the viewfinder can be switched using the menu settings O Zebra pattern and safety zone displays appearing in the viewfinder can be switched using the menu settings Operating precautions Important O This product consists of an SDI card and an interface bracket. [. . . ] power camera off 1 Turn the which to the connected and remove any cables are to the power connector or other connectors. the screws rear 2 Loosen then 4remove theon the itself. panel of the camera, panel the 2 screws on the 3 Loosenthen remove the cover. optional card slot cover, the guides 4 Align the SDI card with inserted. Ensure the card is fully N CARD OPTIO U OUT VIDEO TE I/F REMO CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of fire or electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Rear panel MEN G/L IN ITEM /AWC C IRIS YES/AB AR NO/B DC12V IN Optional card slot cover 5 Firmly tighten the 2 screws to the optional card slot. If the screws are misplaced, use the extra screws supplied with this product. (6 mm in length) secure the rear panel screws. 6 Firmlyscrews are misplaced, with the 4extra screws If the use the supplied with this product. (8 mm in length) SDI card Screws (6 mm) Screws (8 mm) EVF I/F N CARD OPTIO T SDI OU OUT VIDEO TE I/F REMO MEN U G/L IN ITEM /AWC C IRIS YES/AB AR NO/B DC12V IN 5 Interface bracket mountings $ Mounting the bracket on a tripod $ Mounting the viewfinder on a bracket mounting base (supplied 3 Attach the to the top section of interfacewith the viewfinder) bracket using the 2 screws. Mounting base 1 Mount the interface bracket on the tripod. (Screw: 1/4 ­ 20 UNC) 4 Slide the viewfinder onto the mounting base and tighten the fixing knob to secure it firmly. $ Mounting the camera 5 Connect the viewfinder cable to the EVF connector on the interface bracket. EVF I/F cable from the interface camera (in which the SDI 2 Mount theon the interface bracket. card has been 6 Connectto the EVF I/F connector on the SDI card. bracket the installed) Fasten the fixing knob to firmly secure the camera. Fixing knob Fixing knob 6 Connections $ Connected components Convertible camera: AW-E300, AW-E600, AW-E800A, etc. Remote control unit (RCU): WV-RC700A, WV-RC550, etc. Inter-communications headset Video monitor SDI monitor Viewfinder: WV-VF65B, AW-VF80, etc. O Use the RCU cable (AW-CA50A26) to connect the remote control unit to the convertible camera. [. . . ] . 4 Weight and dimensions indicated are approximate. Specifications are subject to change without notice. 10 PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: 3330 Cahuenga Blvd W. , Los Angeles, CA 90068 (323) 436-3500 EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621 Southeast Region: 1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835 Central Region: 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200 WESTERN ZONE: 3330 Cahuenga Blvd W. , Los Angeles, CA 90068 (323) 436-3500 Government Marketing Department: 52 West Gude Drive, Rockville, MD 20850 (301) 738-3840 Broadcast PARTS INFORMATION & ORDERING: 9:00 a. m. [. . . ]