User manual PANASONIC AW-PH405N

[. . . ] Operating Instructions Indoor Pan-tilt Head Model No. AW-PH405N Before operating this product, please read the instructions carefully and save this manual for future use. Printed in Japan F0107Y0 D VQTB0150 Safety precautions FCC Note: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] It is connected to the G/L OUT connector on the AW-RC400 cable compensation unit or other unit. Use a BNC coaxial cable for the connecting cable. CABLE COMP OFF/ON switch [CABLE COMP] When this is set to ON, signals which have been cable compensated for the equivalent of 1640 ft (500 meters) are output from the VIDEO connector and the Y, Pr and Pb connectors. When this switch is used in conjunction with the AW-RC400 cable compensation unit, the video cable can be extended up to a maximum of 81 ft (1000 meters). PROMPTER IN connector [PROMPTER IN] The video signals for the prompter are input to this connector. Use a BNC coaxial cable for the connecting cable. Y connector [Y] This is the output connector for the camera's video signals. It is connected to the Y/VIDEO connector on the AW-RC400 cable compensation unit or monitor, etc. Use a BNC coaxial cable for the connecting cable. Pr/C connector [Pr/C] This is the output connector for the camera's video signals. It is connected to the Pr/C connector on the AW-RC400 cable compensation unit or monitor, etc. Use a BNC coaxial cable for the connecting cable. Pb connector [Pb] This is the output connector for the camera's video signals. It is connected to the Pb connector on the AW-RC400 cable compensation unit or monitor, etc. Use a BNC coaxial cable for the connecting cable. 10 Installation Assembling the pan-tilt head When assembling the pan-tilt head, use the Allen key (provided) and screwdriver, and secure the head by tightening the screws firmly. After mounting the pan-tilt head, check there is no play in its installation. Attaching the camera mounting base Attach the camera mounting base to the rotary arm using the three mounting screws (M5 mm, with flat washers, spring washers) provided. The installation direction differs depending on how the base is installed. Attaching the rotary arm Attach the rotary arm to the rotary head using the four mounting screws (M5 mm, with flat washers, spring washers) provided. The installation direction differs depending on how the arm is installed. For a stand-alone installation Rotary head Camera mounting base Rotary arm For installation on the ceiling Change the guide pin and screw positions as shown in the figure below on the right, and then attach the camera mounting base to the rotary arm. Camera Mounting base Change the positions of the guide pins. Rotary arm Change the positions of the camera mounting screws. Camera mounting base Rotary head 11 Installation Mounting the tally lamp Connect the cable connector which is taped to the top of the pan-tilt head to the tally cable connector. Mount the tally lamp on the top of the pan-tilt head using the two screws provided. Mount the lamp while paying attention to the wire. The cable for the tally cable connector is about -1/16" (50 mm) long. When connecting the cable to the connector, do not pull it out beyond this length. If the tally lamp is not going to be used, insert the cable which is stuck to the top of the pan-tilt head inside the pan-tilt head, and attach the blank panel for the tally lamp using the two screws provided. Tally lamp Blank panel Tally cable connector Taped Note Tighten up the screws securely to ensure that they will not come loose during use. 1 Installation Concerning the safety modes This unit comes with two safety modes which are designed to safeguard the user and others from injury and to prevent damage to the pan-tilt head. 1. Mode for ensuring safety in the case of collisions When the rotary arm of the pan-tilt head or some other unit installed on the head keeps colliding with an obstruction or a person (approx. 6 seconds when the head rotates at 45 degrees per second), the mode for ensuring safety in the case of collisions is established. In this mode, only the rotation of the head in the direction of the collision is stopped. In the case of a low-speed collision, it will take longer for the safety mode to be established. [. . . ] Follow the instructions below to use it to couple the camera to the pan-tilt head. Use the wire mounting screw (M48 mm with flat washer and spring washer) to attach one end of the wire to the pan-tilt head's arm. Use the wire mounting screw (Inch screw with flat washer and spring washer) to attach the other end of the wire on the top panel of the camera. For a stand-alone installation Camera: AK-HC1500G For installation on the ceiling Camera: AK-HC1500G M48 mm wire mounting screw with flat washer and spring washer Wire mounting screw (Inch screw with flat washer and spring washer) Wire mounting screw (Inch screw with flat washer and spring washer) Arm Wire M48 mm wire mounting screw with flat washer and spring washer Be absolutely sure to tighten up the screws securely using a tool such as a screwdriver. Connections Turn off the power of all the equipment before proceeding with the connections. Connect the AC power cable supplied with the AW-PH405 for the AW-PH405 indoor pan-tilt head. [. . . ]