User manual PANASONIC AW-PH600P

[. . . ] Warning: To assure continued FCC emission limit compliance, the user must use only shielded interface cables when connecting to external units. Also, any unauthorized changes or modifications to this equipment could void the user's authority to operate it. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. For CANADA This class A digital apparatus complies with Canadian ICES-003. [. . . ] (AC 120 V, 60 Hz, 120 W) Power switch [POWER ON/OFF] This switch is used to supply AC power to the DC power unit. Keep the switch in the ON position during use. AC adapter mounting screw holes (×4) Attach the supplied pole mounting plate to these screw holes when the AC adapter is to be mounted on a pole or other support. Fuse holder/fuse A fuse for protecting the DC power unit is in the fuse holder. A burnt fuse may be caused by a DC power unit defect. In such a case, consult the store where you purchased it. DC output connector [DC15 V OUT] Connect this connector to the [POWER] connector on the main unit using the supplied power cable. Power LED This lights up red when the power switch is at ON. This is off when the power switch is at OFF. Ventilation opening AC power input cable [AC IN] This is the AC power input cable. It is held in place by the fixed bushing. Cover fastening screws (2) To ensure safety, be absolutely sure to tighten up these screws and close the cover upon completion of the installation work. Cover Loosen the two cover fastening screws and open the cover to proceed with the connections. When closing the cover, first close the cover, and then be absolutely sure to tighten up the two fastening screws. Since malfunctions or other trouble may result if the screws are not tightened enough, be absolutely sure to use a screwdriver to tighten them up. 11 Parts and their functions Supplied cable unit <Multi cable> (VEEB0133) 24P round water-proof plug (male) Connect this to the multi connector [MULTI] on the main unit. G/L IN BNC jack This is the gen-lock signal input jack. Use a BNC coaxial cable for the connecting cable. RJ-45 modular plug Connect this to pan/tilt head controller. To extend the connection, use a relay adapter purchased on the market and use a 10BASE-T straight cable (UTP category 5) for the extension. D-SUB 15P connector (male) Connect the controller used for the multi purpose camera to this connector. When connecting it directly, remove the stud prior to use. For details on how to install the camera and mount, refer to the instructions on the following pages. 17 Installation <When the AW-E350 or AW-E650 camera is used> Use the 2 screws supplied with the camera to attach the mounting adapter (supplied with the camera) to the top panel of the camera. <When the AW-E750 or AW-E860 camera is used> Attach the positioning screw (supplied) to the camera mounting spacer . Attach the positioning screw (supplied) to the camera mounting spacer . Use the 2 screws (supplied) to attach the camera mounting spacer to the fan mounting seat on the top panel of the camera. Use the 2 screws (supplied) to attach the camera mounting spacer to the mounting adapter (supplied with camera) on the top panel of the camera. Attach the camera mount to the camera mounting spacer using the 2 screws , flat washers and spring washers (supplied). (Make sure that the two sides of the camera mount are higher than the central area that is attached. ) Attach the camera mount to the camera mounting spacer using the 2 screws , flat washers and spring washers (supplied). (Make sure that the two sides of the camera mount are higher than the central area that is attached. ) Attach the lens to the camera. Remove the lens hood and zoom lever. Attach the lens to the camera. Remove the lens hood and zoom lever. The camera mount in the opposite direction from when the AW-E655 is used as the camera. To ensure that none of the screws are loose, use a tool to tighten them up securely. 18 Installation <When the AW-E655 camera is used> Attach the positioning screw (supplied) to the camera mounting spacer . <When the AK-HC910 camera is used> Attach the positioning 1 screw (supplied) to the camera mount . Use the 2 screws (supplied) to attach the camera mounting spacer to the fan mounting seat on the top panel of the camera. Attach the camera mount to the fan mounting part on the top panel of the camera using the 1 screw , flat washer and spring washer (supplied). (The camera mount points toward the front or back in the opposite way from a convertible camera. For pointing upward or downward, make sure that the two sides of the camera mount are lower than the central area that is attached. ) Attach the camera mount to the camera mounting spacer using the 2 screws , flat washers and spring washers (supplied). (Make sure that the two sides of the camera mount are lower than the central area that is attached. ) Attach the lens to the camera. Remove the lens hood and zoom lever. Attach the lens to the camera. Remove the lens hood and zoom lever. The camera mount in the opposite direction from when the AW-E750, AW-E860 is used as the camera. To ensure that none of the screws are loose, use a tool to tighten them up securely. 19 Installation <When the AK-HC1500 camera is used> Attach the positioning 1 screw (supplied) to the camera mount . Attach the camera mount using the 2 screws , flat washers and spring washers (supplied). (The camera mount points toward the front or back in the opposite way from a convertible camera. For pointing upward or downward, make sure that the two sides of the camera mount are higher -- which is the opposite from when the AK-HC910 is used -- than the central area that is attached. ) Attach the lens to the camera. Remove the lens hood and zoom lever. The camera mount in the opposite direction from when the AK-HC910 is used as the camera. To ensure that none of the screws are loose, use a tool to tighten them up securely. 20 Installation <When a regular lens is used> Sandwich the housing's support rib between the camera mount and plate nut of the camera on which the camera mount has been installed, and provisionally secure it using the camera mount screws. Housing's support rib Camera mount screws Camera mount Connect the camera with the lens to the interior of the housing using the cable. Upon completion of the connection, loosen the camera mount screws, and move the entire camera so that the front of the camera lens comes as close as possible to the inside surface of the glass. [. . . ] Press the battery in the direction shown by the arrow in the figure, and pull the battery out to remove it completely. Installing the new battery Position the new battery with its "+" side facing down, insert one end into the holder in the direction indicated by the arrow , and push it into place. Attach the main unit cover and sunshade cover using the 5 screws for each cover. Sunshade cover Main unit cover Lithium battery 34 Replacement of consumable parts Replacing the motor Replace the motor when it ceases to operate properly. For details on the motor replacement, consult your dealer. Replacing the belt Replace the belt when the preset stop accuracy has deteriorated. For details on the belt replacement, consult your dealer. Replacing the gear Replace the gear when the preset stop accuracy has deteriorated. [. . . ]