User manual PANASONIC AW-PH650N

[. . . ] AW-PH650N Outdoor Pan/Tilt Head Before attempting to connect, operate or adjust this product, please read these instructions completely. Printed in Japan F0406Y1056 D VQTB0104-1 Safety precautions FCC Note: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] 1 9 2 10 3 11 4 12 5 13 6 14 7 15 8 Signal name ­­­ ­­­ ­­­ ­­­ ­­­ ­­­ ­­­ GND ­­­ TXD (C) ­­­ RXD (H) TXD (H) RXD (C) ­­­ VIDEO OUT BNC jack This is the output connector for the camera's video signals. Use a BNC coaxial cable for the connecting cable. Y OUT BNC jack This is the output connector for the camera's video signals. Use a BNC coaxial cable for the connecting cable. Pr OUT BNC jack This is the output connector for the camera's video signals. Use a BNC coaxial cable for the connecting cable. Pb OUT BNC jack This is the output connector for the camera's video signals. Use a BNC coaxial cable for the connecting cable. 12 Parts and their functions <Power cable> (VEEB0152) 7P round water-proof plug (female) Connect this to the power connector [POWER] on the main unit. 7P round water-proof plug (male) Connect this to the DC output connector [DC 15V OUT] on the AC adapter. <Convertible camera cable> (VEEB0176) 26P connector (male) Connect this to the CAMERA I/F connector [CAMERA I/F] on the housing. 50P connector (male) Connect this to the CAMERA I/F connector [CAMERA I/F] on the convertible camera. <AK-HC900 series cable> (VEEB0177) 26P connector (male) Connect this to the CAMERA I/F connector [CAMERA I/F] on the housing. D-SUB 15P connector (female) Connect this to the I/F connector [CAMERA I/F] on the AK-HC900 series. <AK-HC1500 cable> (VEEB0178) 26P connector (male) Connect this to the CAMERA I/F connector [CAMERA I/F] on the housing. High-density D-SUB 15P connector (male) Connect this to the I/F connector [I/F] on the AK-HC1500. 13 Installation Installing the housing mount frame Attach the housing mount frame (supplied) to the rotary arm of the main unit. Attach the housing mount frame to the rotary arm as shown in the figure below. The screws must be installed together with the flat washers and spring washers (supplied). · Using the supplied Allen key, install the frame securely to prevent looseness in the four places where the screws are used. Rotary arm Housing mount frame Allen key <Housing mount frame installed on rotary arm> 14 Installation Cable compensation circuit settings When the pan/tilt head and controller have been connected, the maximum allowable length of the connecting cables is 3281 ft. (1000 m) for the 10BASE-T straight cable (UTP category 5) and coaxial cable (BELDEN 8281). However, when using the cables beyond a distance of 1640 ft. (500 m), set the cable compensation circuit to ON by following the steps. (The factory setting is OFF. ) Remove the five screws used to attach the sunshade cover to keep direct sunlight off the unit, and remove this cover. Remove the five screws used to attach the pan/tilt head main unit cover, and remove this cover. Set the SW1 on the internal COMP circuit board to ON. Return the main unit cover and sunshade cover to their original positions, and use the mounting screws to fasten them securely. Sunshade cover Main unit cover COMP circuit board <COMP circuit board> Set to ON. The selector switch When sending HD analog component signals using the AK-HC910 or AK-HC900, set SW2, SW3 to HD. At this switch setting, the cable compensation circuit will not work even if SW1 is set to ON so set SW1 to OFF. 15 Installation CPU circuit board switch settings Set switches SW1, SW2 and SW3 on the CPU circuit board as follows. SW2 SW1 SW3 SW1 (Selector switch for landing characteristics) For a soft landing: Set SW1 to the left position (RP501). (Factory setting) For an exact landing: Set SW1 to the right position (RP605). SW2 Do not change the position of this switch. Continue to use it at the DESK TOP position. SW3 Do not change the position of this switch. Continue to use it at the RS-422 position. · Before setting these switches, be absolutely sure to turn off the power of the AC adapter connected to the pan/tilt head. · The switch settings are not changed simply by changing the position of the switches. After changing the position of a switch, turn the power off and then back on to actually change the setting of that switch. 16 Installation How to install the camera Loosen the bolts for opening and closing the top cover, and open the top cover. Remove the camera mount. Loosen the top cover open/close bolts Install the camera on the camera mount. The support arm completely enters the groove. Open the top cover until the support arm completely enters the groove. Bear in mind that it will not be possible to lock the top cover if the arm is not completely in. [. . . ] For details on the gear replacement, consult your dealer. The motor, gear and belt are consumables. They need to be replaced at periodic intervals. 35 Appearance Main unit Unit: inch (mm) 8-3/8 (213) 9-5/16 (237) 13-1/8 (333) 6-11/16 (170) 5-7/8 (149) 20-1/8 (511) 7-1/2 (190) 3/16-ø3/8 (4-ø10) hole 6-5/16 (160) 6-11/16 (170) 36 5-1/2 (140) Appearance Housing unit Unit: inch (mm) 10-1/2 (266) 1-7/8 (48) 9-11/16 (246) 27 (685) 37 Appearance AC adapter unit Unit: inch (mm) 7-7/8 (200) 5-3/4 (146) 4-M8 nut 7/8 (22) 11 (280) 3-7/8 (98) 2-7/16 (62) 7-7/8 (200) 38 3/8 (10) 4-3/4 (121) When an IAS, WAS or VAS lens (analog drive) made by Canon is used Connector: SR30-10PE-6P (74) made by Hirose Electric Connect to the FOCUS connector on lens. Cable length: At least 800 mm or so Connector: 10136-3000VE made by Sumitomo 3M Case: 10336-52F0-008 made by Sumitomo 3M Connector: R01-01P9-8M made by Tajimi Musen Connect to the ZOOM connector on the lens. Cable length: At least 800 mm or so Cable specifications Connector: HR10A-10J-12S (73) made by Hirose Electric 39 Connect to the LENS I/F2 connector in housing. [. . . ]