User manual PANASONIC AWRC400N

[. . . ] AW-PH400P Pan/Tilt Control Panel AW-RP400N Cable Compensation Unit AW-RC400N Roll Unit AW-RL400G Indoor Pan/Tilt Head AW-PH400 AW-RP400 AW-RC400 AW-RL400 Before attempting to connect, operate or adjust this product, please read these instructions completely. AW-RL400 AW-RC400 AW-RP400 AW-PH400 Safety precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] When REVERSE is selected, the lens focus moves in the opposite direction. When NORMAL is selected, the lens iris moves toward open when the IRIS dial is turned clockwise and toward closed when it is turned counterclockwise. When REVERSE is selected, the lens iris moves in the opposite direction. TILT: ZOOM: FOCUS: IRIS: ROTATION: When NORMAL is selected, the pan/tilt head moves clockwise when the top of the ROTATION control switch is pressed and counterclockwise when the bottom is pressed. When REVERSE is selected, the head moves in the opposite direction. TILT RANGE setting (190/300 degrees) This menu item is used to set the tilting range of the AW-PH400. Normally, the 190 degrees setting is used. SPEED WITH ZOOM POS. setting (OFF/1/2/3) At the OFF setting, the pan and tilt speed does not change in accordance with the zoom position. At the 1, 2 or 3 setting, the panning and tilting of the pan/tilt head slows down as the zoom approaches the telephoto end, making it easier to adjust the pan or tilt position even at the telephoto end. The higher the number selected for the setting, the slower the pan and tilt speed at the telephoto end, and the easier it is to adjust the position using a zoom lens with a high magnification rate. PRESET SPEED setting (1 to 25) During preset memory data play, this menu item enables the movement speed to the preset positions to be set to one of 25 steps. The higher the setting, the faster the movement speed to the preset positions; conversely, the lower the setting, the slower the movement speed. IRIS CONTROL setting (BOTH/RP400/CB400) When the AW-CB400 remote operation panel has been connected to the AW-RP400 control panel, this menu item is used to set which control panel is to be used to adjust the lens iris. At the BOTH setting, the lens iris can be controlled from both the AW-RP400 and AW-CB400. At the RP400 setting, it can be controlled only from the AW-RP400; similarly, at the CB400 setting, it can be controlled only from the AW-CB400. ROTATION SWITCH setting (ROTATION/FOCUS/ZOOM/IRIS) This menu item enables ROTATION, FOCUS, ZOOM or IRIS to be selected as the function to be controlled by the ROTATION switch. 30 Pan/Tilt Control Panel AW-RP400 Menu settings OPTION SWITCH A to H settings (NOT USE / DEF / WIP / HEATER/FAN / LAMP / OPTION / ND / EXT / AF) The following functions can be allocated to OPTION buttons A to H. Different functions can be allocated for different pan/tilt heads. This controls the ON and OFF states of the defroster function when using a pan/tilt head system equipped with this function. Each time the button is pressed, ON is switched to OFF or vice versa. When the defroster function is ON, the lamp of the button to which this function has been allocated is lighted; when it is OFF, the lamp is off. WIP: HEATER/FAN: This controls the ON and OFF states of the heater/fan function when using a pan/tilt head system equipped with this function. Each time the button is pressed, ON is switched to OFF or vice versa. When the heater/fan function is ON, the lamp of the button to which this function has been allocated is lighted; when it is OFF, the lamp is off. LAMP: This controls the ON/OFF switching of the power from the AC outlet which is used for the AC adaptor's lamp when using an AC adaptor for a pan/tilt head provided with a lamp control function. Each time the button is pressed, ON is switched to OFF or vice versa. When the lamp is ON, the button to which the function is allocated lights; when it is OFF, the button goes off. If the lamp fails at the ON setting, the button blinks. This controls the short-circuit and open-circuit states of the AC adaptor's OPTION CONTROL OUT connector when using an AC adaptor for a pan/tilt head system equipped with the OPTION switch control function. [. . . ] 4 If necessary, register other shooting positions and settings in PRESET MEMORY buttons 1 to 50 as preset memory data. 5 Select another pan/tilt head system using the CONTROL SELECT button, and proceed with the preset memory data settings for the pan/tilt head system concerned. Repeat this step for all the pan/tilt head systems. 56 Operating procedures Playing the preset memory data 1 Select the pan/tilt head system using one of the CONTROL SELECT buttons. 2 When the button corresponding to the registered preset memory data is pressed, the pan/tilt head system is set to the registered status. 57 When an IAS, WAS or VAS lens (analog drive) made by Canon is used Connector: SR30-10PE-6P made by Hirose Electric Connect to the FOCUS connector on lens. [. . . ]