User manual PANASONIC AW-RC600P

[. . . ] AW-RC600P Remote Control Unit Before attempting to connect, operate or adjust this product, please read these instructions completely. Safety precautions FCC Note: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] Note: The ALC cannot be finely adjusted and the lens iris cannot be adjusted when the iris selector switch on the lens is set to a position other than [AUTO] (such as [MANU]). With some lenses, the open and close directions with respect to the control directions may be reversed. If this is the case, contact the lens manufacturer or your dealer. Intercom volume adjustment control [INCOM LEVEL] This is used to adjust the volume of the sound heard through the speaker of the headset connected to the INCOM connector. 9 Parts and their functions Horizontal phase adjustment control [H. PHASE] This is used to adjust the horizontal phases of the gen-lock input and video output when two or more cameras are used at the same time. Chroma gain adjustment control [ADJUST CHROMA] This is used to adjust the chrominance level of the video output signals to match the cable length. (Select the cable length using the cable compensation selector switch and adjust the Y level of the video output signals using the Y gain adjustment control before adjusting the level. ) Subcarrier phase coarse adjustment switch [SC COARSE] This is used to adjust the hue of the gen-lock input and video output coarsely when two or more cameras are used at the same time. When used in combination with the subcarrier phase fine adjustment control , the adjustable range is greater than 360 degrees. Menu ON/OFF switch [MENU OFF/ON] OFF: Only the camera's images are output to the video output. ON: The camera's images and superimposed camera's menu are output to the video output. Menu items can be selected and data changed using the item UP switch , item DOWN switch , DATA YES/UP switch and DATA NO/DOWN switch . For details on the menu items and contents, refer to the camera's operating instructions. Subcarrier phase fine adjustment control [SC FINE] This is used to adjust the hue of the gen-lock input and video output finely when two or more cameras are used at the same time. When used in combination with the subcarrier phase coarse adjustment switch , the adjustable range is greater than 360 degrees. Item UP switch [ITEM UP] When this is pressed while a menu is displayed, the item which is the next one up from the current item on the menu can be selected. Cable compensation selector switch [COARSE] This is set in line with the length of the cable between the camera and RCU. Switch position 1 2 3 4 Cable length Less than 246 ft. (230 to 300 m) Item DOWN switch [ITEM DOWN] When this is pressed while a menu is displayed, the item which is the next one down from the current item on the menu can be selected. (The cable lengths above are approximations only. ) DATA YES/UP switch [DATA YES/UP] When this is pressed while the main menu is displayed, the submenus of the items are displayed. When it is pressed while a submenu is displayed, the setting is incremented. Y gain adjustment control [ADJUST Y] This is used to adjust the Y (luminance) level of the video output signals to match the cable length. (Select the cable length using the cable compensation selector switch before adjusting the level. The chroma amount is also varied by this control. ) DATA NO/DOWN switch [DATA NO/DOWN] When this is pressed while the main menu is displayed, the item which is the next one down from the current item on the menu can be selected. When it is pressed while a submenu is displayed, the setting is decremented. 10 Parts and their functions Rear panel Camera cable connector [CAMERA] (26-pin connector) The camera's cable (such as the AW-CA50A26) is connected here. Contact-type pan/tilt head control connector [PAN/TILT CONTROL IN] (D-SUB 15-pin connector) This has the same shape as the tally/intercom input/ output connector. Take care not to confuse the two when connecting them. A controller for controlling the lens (a lens with zoom and focus servo) and pan/tilt head (up, down, left, right, defroster, wiper, etc. ) is connected here. (Only a contact-type controller can be connected. ) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Signal Name LEFT RIGHT UP DOWN FAR NEAR TELE WIDE DEFROSTER WIPER COMM +5 V +V (+7. 5 V) ­V (+2. 5 V) GND Ensure that both the LEFT and RIGHT pins are not connected to the COMM pin at the same time. Similarly, do not connect both the UP and DOWN, FAR and NEAR or WIDE and TELE pins to the COMM pin at the same time. Pins #12 to #15 are used when exercising lens control only. To do this, connect the controller's FOCUS CONT pin to NEAR (pin #6) and its ZOOM CONT pin to WIDE (pin #8). [. . . ] Press the item DOWN switch to select the item which is the next one down from the current item on the menu. When the DATA YES/UP switch is pressed while the main menu is displayed, the submenus of the items are displayed. When it is pressed while a submenu is displayed, the setting is incremented. When the DATA NO/DOWN switch is pressed while the main menu is displayed, the item which is the next one down from the current item on the menu. [. . . ]